Metering Pump (Steering) - Assemble
Note: Make sure that all parts of the steering metering pump are clean prior to assembly. During assembly, apply clean SAE 10 oil on the internal parts of the steering metering pump.
- Check the condition of all O-ring seals. If any seal is worn or damaged, use a new part for replacement.
Show/hide table
Illustration 1 g00842687 - Install O-ring seals (23) and (25) on seat (24).
- Install retainer (27), ball (26), seat (24) and plug (22) in the pump body. The torque for plug (22) is
11 ± 2 N·m (8 ± 1 lb ft) .Note: The plug must not protrude from the surface of the pump body. The plug must be flush with the surface of the pump body or the plug must be below the surface of the pump body.
Show/hide tableIllustration 2 g00278658 - Install seals (20) in bushing (21).
Show/hide table
Illustration 3 g00278657 Show/hide tableIllustration 4 g00278616 - Install O-ring seal (19) in the pump body. Install bushing (18) and spiral lockring (17).
Show/hide table
Illustration 5 g00278615 - Turn the pump body onto the opposite side. Install bearing races (15) and bearing (16) in the pump body.
Show/hide table
Illustration 6 g00279553 - Assemble the sleeve assembly, as follows:
- Install six springs (13) in spool (12). There must be three springs on each side. Make sure that the curves of the springs are in contact and in the center of the spool. The notched side of the spring ends must face toward the sleeve.
- Install sleeve (11) over spool (12). The notch in the sleeve must engage with the ends of spring (13).
- Install pin (14).
Show/hide tableIllustration 7 g00279555 - Install sleeve assembly (10) in the pump body.
- Install O-ring seal (9) in the pump body.
Show/hide table
Illustration 8 g00279557 - Install spacer (8) and drive (7) in the pump body. Make sure that the notch in drive (7) engages with pin (14) in the sleeve assembly.
Show/hide table
Illustration 9 g00278609 - Install O-ring seal (6) in gerotor assembly (4).
Show/hide table
Illustration 10 g00278608 Show/hide tableIllustration 11 g00279603 - Install gerotor assembly (4) and spacer (5) in the pump body. Make sure that gerotor assembly (4) is aligned with pin (14) in the sleeve assembly, as shown.
Show/hide table
Illustration 12 g00278607 - Install O-ring seal (3) in cap (2).
Show/hide table
Illustration 13 g00278434 - Position cap (2) on the gerotor assembly.
- Install seven bolts (1). Tighten the bolts in the following manner:
- Tighten the bolts in the numerical sequence that is shown in Illustration 14. The initial torque for the bolts is
14 ± 3 N·m (10 ± 2 lb ft) . - Tighten the bolts again in the numerical sequence that is shown in Illustration 14. The final torque for the bolts is
28 ± 3 N·m (21 ± 2 lb ft) .
Show/hide tableIllustration 14 g00361939 - Tighten the bolts in the numerical sequence that is shown in Illustration 14. The initial torque for the bolts is
End By:
- Install the steering metering pump. Refer to Disassembly and Assembly, "Metering Pump (Steering) - Install".
Caterpillar Information System:
966G Wheel Loader and 972G Wheel Loader Machine Systems Metering Pump (Steering) - Disassemble
902 and 906 Compact Wheel Loaders Pallet Forks Operation
902 and 906 Compact Wheel Loaders Cab Door
3408E and 3412E Engines for Caterpillar Built Machines Crankcase Breather
966G Wheel Loader and 972G Wheel Loader Machine Systems Heater Coil - Remove and Install
966G Wheel Loader and 972G Wheel Loader Engine Supplement Hood Tilt Actuator - Remove
990 and 990 Series II Wheel Loader and 844 Wheel Tractor Power Train Differential and Bevel Gear
966G Wheel Loader and 972G Wheel Loader Machine Systems Evaporator Coil - Remove and Install
953C Track-Type Loader Power Train Speed Control (Override and Brake)
902 and 906 Wheel Loaders Piston Motor (Hydrostatic)
966G Wheel Loader and 972G Wheel Loader Machine Systems Seat - Remove and Install
854G Wheel Dozer Hydraulic System Hydraulic Oil Contamination - Test
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Steering Wheel - Remove and Install
994D Wheel Loader Hydraulic System Temperature Sensor (Hydraulic Tank)
3408E and 3412E Engines for Caterpillar Built Machines Housing (Front)
994D Wheel Loader Hydraulic System Tilt Cylinder
854G Wheel Dozer Hydraulic System Relief Valve (Pilot)
953C Track-Type Loader Power Train Screen Group
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Steering Control Valve - Command Control Steering
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Orifice Tube System
953C Track-Type Loader Hydraulic System Diverter Valve
953C Track-Type Loader Hydraulic System Bucket Control
953C Track-Type Loader Power Train Hydraulic Oil Filter
D6G Track-Type Tractor Power Train Sprocket Segment - Remove and Install