Radiator - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 4     |
- Position radiator mounting group (1) in radiator frame (3) . Install four bolts (2) , the nuts, and the washers that fasten radiator mounting group (1) to radiator frame (3) .
Show/hide table
Illustration 1 | g00288801 |
- Install the remaining radiator mounting group in the same manner as Step 1 .
- Place radiator frame (3) in an upright position. Fasten a hoist, nylon lifting straps, and Tooling (A) to radiator group (4) , as shown. Carefully position radiator group (4) in radiator frame (3) .
Show/hide table
Illustration 2 | g00288803 |
Note: Do not damage radiator group (4) during the installation of radiator group (4) in radiator frame (3) .
- Install coolant recovery tank (5) on the radiator assembly.
Show/hide table
Illustration 3 | g00288804 |
- Install hose (6) to coolant recovery tank (5) .
Show/hide table
Illustration 4 | g00288805 |
- Connect hose (8) to coolant recovery tank (5) . Tighten hose clamp (7) to hose (8) .
- Install two bolts (9) , the washers, and the nuts to both sides of radiator assembly (10) .
Show/hide table
Illustration 5 | g00287046 |
- Install plate assembly (11) to radiator assembly (10) . Install four bolts (12) and the washers in plate assembly (11) .
Show/hide table
Illustration 6 | g00287568 |
- Install plate assembly (14) to radiator assembly (10) . Install four bolts (13) and the washers in plate assembly (14) .
- Place radiator assembly (10) on the floor, as shown.
Show/hide table
Illustration 7 | g00287567 |
- Install locknuts (15) and the washers to two studs (16) .
- Tighten locknuts (15) to a torque of 64 ± 4 N·m (47 ± 3 lb ft) .
- Place radiator assembly (10) on the floor, as shown.
Show/hide table
Illustration 8 | g00287546 |
- Install the six bolts in the front of the fan blade. Carefully install fan blade (17) in radiator assembly (10) .
End By: Install the radiator. Refer to Disassembly and Assembly, "Radiator - Install", that is in this module.
Caterpillar Information System:
611 Wheel Tractor-Scraper 3306B Engine Supplement Fan and Fan Drive - Remove
966G and 972G Wheel Loaders Autoshift Control - Earlier Machines
3306B Industrial Engine Walk-Around Inspection
613C Series II Wheel Tractor 3116 Engine Supplement Radiator - Disassemble
966G and 972G Wheel Loaders Transmission Control - Conventional Steering
953C Track-Type Loader Tracks
953C Track-Type Loader Bucket Positioner
953C Track-Type Loader Monitoring System
994 Wheel Loader Steering System Steering Metering Pump
953C Track-Type Loader Light Switches
966G and 972G Wheel Loaders Transmission Control - Command Control Steering
992G Wheel Loader Electrohydraulic System Pilot Control Actuator Current (Proportional Solenoid) - Check
966G and 972G Wheel Loaders Implement Lockout Control
994 Wheel Loader Hydraulic System Linkage Pin and Seal Group (Bucket Control)
953C Track-Type Loader Shipping the Machine
953C Track-Type Loader Stopping the Engine
953C Track-Type Loader Changing Direction and Speed
953C Track-Type Loader Cutting Edges and Bucket Teeth
953C Track-Type Loader Equipment Lowering with Engine Stopped
953C Track-Type Loader Leaving the Machine
953C Track-Type Loader Lift Kickout
953C Track-Type Loader Operation Information
966G and 972G Wheel Loaders Hydraulic Control Support
966G and 972G Wheel Loaders Lift Control