Fuel Manifold - Remove
Removal Procedure
Start By:
- Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolt (2) and move the harness assembly out of the way.
Show/hide table
 | |
| Illustration 1 | g00846247 |
- Remove bolts (3) .
- Remove fuel manifold (1) .
- Remove O-ring seals (4) from fuel manifold (1) .
Show/hide table
 | |
| Illustration 2 | g00846262 |
- Remove plugs (5) and the O-ring seals, if necessary.
Caterpillar Information System:
C15 On-highway Engines Exhaust Manifold - Remove and Install
C9 Marine Generator Set Engines Engine Valve Lash - Inspect/Adjust
C-10 Petroleum Engine Electronic Unit Injector - Install
C-10 Petroleum Engine Electronic Unit Injector - Remove
C-10 Petroleum Engine Fuel Transfer Pump - Install
C-10 Petroleum Engine Fuel Transfer Pump - Remove
C-10 Petroleum Engine Fuel Filter Base - Install
C-10 Petroleum Engine Fuel Filter Base - Remove
G3516B Engines MID 036 - CID 1446 - FMI 09 Unable to communicate with Fuel Metering Module
G3516B Engines MID 036 - CID 1446 - FMI 09 Unable to communicate with Fuel Metering Module
G3516B Engines MID 036 - CID 1446 - FMI 05 Fuel Metering Module open circuit
C-10 Petroleum Engine Fuel Priming Pump - Remove and Install
C-10 Petroleum Engine Fuel Manifold - Install
C27 and C32 Engines for Caterpillar Built Machines CID 0094 FMI 03 Fuel Pressure open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0094 FMI 04 Fuel Pressure short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0100 FMI 04 Engine Oil Pressure short to ground
C-10 Petroleum Engine Electronic Unit Injector Sleeve - Remove
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 04 Engine Coolant Temperature short to ground
C27 and C32 Generator Set Engines CID 0174 FMI 03 Fuel Temperature open/short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C32 Marine Engines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C32 Marine Engines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground