Electronic Unit Injector Sleeve - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A (1)     | 221-9778     | Puller Stud     | 1     |
128-7889 | Bridge Puller     | 1     | |
9U-6877 | Thrust Bearing     | 1     | |
5P-8247 | Hard Washer     | 1     | |
4K-0367 | Nut     | 1     |
Show/hide table
( 1 ) | Tooling (A) is part of the 9U-6891 Injector Tool Group . |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Install Tooling (A) into unit injector sleeve (1) .
Show/hide table
Illustration 1 | g01076889 |
- Tighten the nut until unit injector sleeve (1) is pulled free of the cylinder head assembly.
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines CID 0100 FMI 04 Engine Oil Pressure short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0094 FMI 04 Fuel Pressure short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0094 FMI 03 Fuel Pressure open/short to +batt
C-10 Petroleum Engine Fuel Manifold - Install
C-10 Petroleum Engine Fuel Manifold - Remove
C15 On-highway Engines Exhaust Manifold - Remove and Install
C9 Marine Generator Set Engines Engine Valve Lash - Inspect/Adjust
C-10 Petroleum Engine Electronic Unit Injector - Install
C-10 Petroleum Engine Electronic Unit Injector - Remove
C-10 Petroleum Engine Fuel Transfer Pump - Install
C-10 Petroleum Engine Fuel Transfer Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 04 Engine Coolant Temperature short to ground
C27 and C32 Generator Set Engines CID 0174 FMI 03 Fuel Temperature open/short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C32 Marine Engines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C32 Marine Engines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C9 Marine Generator Set Engines Cooling System - Test
C11 and C13 Petroleum Engines Coolant Conditioner Base
G3500 Engines Product Storage
C7 Urban Transit Bus Engines Cooling System Coolant Extender (ELC) - Add
C7 Marine Engines Heat Exchanger - Remove
325D and 329D Excavators Fuel Tank Shutoff and Drain Control