Heat Exchanger - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 1     |
Start By:
- Remove the transmission oil cooler and the auxiliary oil cooler. Refer to Disassembly and Assembly, "Oil Cooler (Transmission, Auxiliary) - Remove and Install".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
- Disconnect tube assemblies (1) and (2) .
Show/hide table
Illustration 1 | g01237249 |
- Disconnect tube assemblies (3) and (4) .
Show/hide table
Illustration 2 | g01237251 |
- Disconnect hoses (5) , (6) , and (7) .
Show/hide table
Illustration 3 | g01237252 |
- Attach Tooling (A) and a suitable lifting device to heat exchanger (8) .
Show/hide table
Illustration 4 | g01237253 |
- Remove bolts (9) .
Show/hide table
Illustration 5 | g01237255 |
- Remove bolts (10) . Remove heat exchanger (8) . The weight of heat exchanger (8) is approximately 51 kg (112 lb).
Show/hide table
Illustration 6 | g01237256 |
Caterpillar Information System:
C7 Urban Transit Bus Engines Cooling System Coolant Extender (ELC) - Add
G3500 Engines Product Storage
C11 and C13 Petroleum Engines Coolant Conditioner Base
C9 Marine Generator Set Engines Cooling System - Test
C32 Marine Engines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C32 Marine Engines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C27 and C32 Generator Set Engines CID 0174 FMI 03 Fuel Temperature open/short to +batt
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 04 Engine Coolant Temperature short to ground
C11 and C13 Engines for Caterpillar Built Machines CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C-10 Petroleum Engine Electronic Unit Injector Sleeve - Remove
C27 and C32 Engines for Caterpillar Built Machines CID 0100 FMI 04 Engine Oil Pressure short to ground
325D and 329D Excavators Fuel Tank Shutoff and Drain Control
320D Excavator Fuel Tank Water and Sediment - Drain
G3520B Industrial Engine System Overview
2004/07/05 249-2813 Water Filter Gp is Available for Shop Applications that Require Water Filtration {0699}
Installation of the 254-4334 Check Valve Kit on the 228-5896 Unit Injector Hydraulic Pump Gp and the 228-5898 Unit Injector Hydraulic Pump Gp {1714} Installation of the 254-4334 Check Valve Kit on the 228-5896 Unit Injector Hydraulic Pump Gp and the 228-5898 Unit Injector Hydraulic Pump Gp {1714}
G3520B Industrial Engine Location of Components
C7 Marine Engines Heat Exchanger - Install
345C MHPU Mobile Hydraulic Power Unit Engine Starting
C7 Marine Engines Oil Cooler (Transmission, Auxiliary) - Remove and Install
2004/07/01 New Cylinder Head Group {1100}
C15 On-Highway Engine Engine Oil Pump - Remove
C15 On-Highway Engine Engine Oil Pump - Install