Air Inlet Heater - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud (M10 x 1.50 x 60 mm) |
2 |
B | - | Guide Stud (M8 x 1.25 x 90 mm) |
2 |
C | 4C-9500 | Quick Cure Primer | - |
D | 1U-8846 | Gasket Sealant | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Thoroughly clean the mating surfaces of the cylinder head, the air inlet heater, and the base assembly.
Show/hide table
Illustration 1 g01109446 - Install Tooling (B) in the cylinder head at Location (Z).
- Apply Tooling (C) to both sides of air inlet heater (16) and base assembly (14).
- Allow Tooling (C) to dry for three to five minutes.
- Apply Tooling (D) to both sides of air inlet heater (16) and install air inlet heater (16) on Tooling (B).
Note: The air inlet heater and the base assembly must be installed within ten minutes of applying Tooling (D).
- Position base assembly (14) on Tooling (B).
- Install bolts (13) and bolts (15) finger tight.
- Remove Tooling (B) and install remaining bolts (13). Tighten bolts (13) and bolts (15).
- Connect inlet air temperature sensor (12).
- Connect harness assembly (11) at the air inlet heater.
- Install Tooling (A) in the base assembly at Location (Y).
Show/hide table
Illustration 2 g01046232 - Attach a suitable lifting device to core assembly (4) at Location (X). The weight of core assembly (4) is approximately
36 kg (80 lb) . Install core assembly (4) on the base assembly and Tooling (A). - Position cover (2) onto Tooling (A).
- Install bolts (3).
- Remove Tooling (A). Install remaining bolts (3).
- Install tube assembly (8) and hose (9).
- Install tube assembly (6). Install bolts (7).
- Install support (10).
- Install adapter (5).
- Connect harness assembly (1) to the air inlet heater switch.
Caterpillar Information System:
C9 Marine Engines and C9 Marine Generator Sets Air Inlet Heater - Remove
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Sensor
G3500 Engines Fumes Disposal System
C7 Marine Engine Fuel Filter Base
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove
G3500 Engines Crankcase Breather
2004/11/01 Improved Fan Drives are Used {1359}
C7 Marine Engine Flywheel Housing
G3500 Engines Engine Oil Level Regulator
C12 Marine Engines Engine Crankcase Breather - Clean
C12 Marine Engines Engine Air Cleaner Service Indicator - Inspect
3126B Petroleum Engine Auxiliary Water Pump
C7 Marine Engine Fuel Pressure Sensor - If Equipped
2004/03/29 Thermocouple Assembly (Exhaust) Measures Engine Exhaust Temperatures {0701, 0776, 0781}
C7 Marine Engine Engine Oil Temperature Sensor
C7 Marine Engine Coolant Level Sensor - If Equipped
C32 Marine Engine Cooling System
C32 Marine Engine Exhaust Temperature - Test
C32 Marine Engines Aftercooler - Test
C32 Marine Engine Cooling System - Check - Overheating
C15 Petroleum Generator Set Engines Inlet Manifold Air Pressure Sensor
C32 Marine Engine Cooling System - Test
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Maintenance Interval Schedule