Marine Transmission Oil Cooler - Remove and Install
Start By:
- Remove the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect the marine transmission oil cooler lines from the marine transmission oil cooler.
Show/hide table
Illustration 1 g01030443 - Disconnect hose (1).
- Remove bolts (3).
- Remove transmission oil cooler (2).
Show/hide table
Illustration 2 g01030366 - Remove bolts (4). Remove cover (5).
- Remove bolts (8). Remove cover (9) and flange (10) from housing (7). Remove O-ring seal (6).
- Remove core assembly (11). Remove O-ring seals (6).
- Remove plug (13) and remove zinc plug (12).
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-3931 | Anti-Seize Compound | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install O-ring seals (6) on core assembly (11).
- Install core assembly (11) in housing (7). Install cover (5) and install bolts (4).
- Install flange (10), O-ring seal (6), and cover (9) on housing (7). Install bolts (8).
- Install zinc plug (12). Install plug (13).
Show/hide table
Illustration 4 g01030443 - Position marine transmission oil cooler (2) and install bolts (3).
- Connect hose (1).
- Apply Tooling (A) on the threads of the marine transmission oil lines. Install the marine transmission oil lines.
- Fill the marine transmission to the correct level. Refer to the Operation and Maintenance Manual, "Marine Transmission Oil Level - Check".
Show/hide table
Illustration 3 | g01030366 |
End By:
- Install the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Install".
Caterpillar Information System:
C9 Marine Engines and C9 Marine Generator Sets Engine Oil Cooler - Install
C9 Marine Engines and C9 Marine Generator Sets Engine Oil Cooler - Remove
C9 Marine Auxiliary and Generator Set Engines Fuel Conservation Practices
C7 On-highway Engine Inlet Air Temperature Sensor - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Cooling System - Inspect
3408C, 3412C and 3412D High Performance Marine Engines Cooling System - Test
3408C, 3412C and 3412D High Performance Marine Engines Charging System - Test
C7 On-highway Engine Boost Pressure Sensor - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Piston Ring Groove - Inspect
C7 On-highway Engine Injection Actuation Pressure Sensor - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Fuel System Pressure - Test
3408C, 3412C and 3412D High Performance Marine Engines Fuel System - Inspect
C9 Marine Engines and C9 Marine Generator Sets Engine Oil Pump - Remove
C9 Marine Engines and C9 Marine Generator Sets Engine Oil Pump - Install
3408C, 3412C and 3412D High Performance Marine Engines Air Inlet and Exhaust System
3516B HD Generator Set Cold Weather Operation
C15 and C18 Petroleum Generator Sets Before Starting Engine
C9 Marine Auxiliary and Generator Set Engines Starting the Engine
C9 Marine Auxiliary and Generator Set Engines Cold Weather Starting
C9 Marine Engines and C9 Marine Generator Sets Electric Starting Motor - Remove and Install
EMCP3 Setpoint Programming
EMCP3 Electronic Control Module (Generator Set)
3516B HD Generator Set After Starting Engine
C9 Marine Engines and C9 Marine Generator Sets Coolant Level Sensor - Remove and Install