Electronic Unit Injector Sleeve - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-3042 | Plug Tap | 1 |
| B | 9U-6858 | Bridge Plate | 1 |
| 9U-6891 | Injector Tool Group | 1 | |
| C | 221-9803 | Rubber Stopper | 1 |
| D | 4C-6774 | Vacuum Gun Kit | 1 |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position Tooling (C) at the bottom of the electronic unit injector sleeve. This will prevent debris from entering the cylinder during the removal of the electronic unit injector sleeve.
Show/hide table
Illustration 1 g01108482 - Coat Tooling (A) with clean grease. Use Tooling (A) to cut threads into electronic unit injector sleeve (1).
Show/hide table
Illustration 2 g01108474 - Install Tooling (B) in electronic unit injector sleeve (1).
- Use Tooling (B) to remove the electronic unit injector sleeve.
- Remove Tooling (B) and Tooling (C) from electronic unit injector sleeve (1).
Note: Do not reuse the electronic unit injector sleeve.
- Use Tooling (D) to remove any debris from the bore for the electronic unit injector sleeve.
Caterpillar Information System:
G3500 Engines Gear Group (Front) - Reverse Rotation
3408C, 3412C and 3412D High Performance Marine Engines Electronic Control System Components
2003/10/01 Proper Termination Techniques May Increase Digital Voltage Regulator (DVR) Reliability {4467}
2003/10/01 The Water Resistance of the Wiring Harness Has Improved {1408}
3408C, 3412C and 3412D High Performance Marine Engines General Information
3408C, 3412C and 3412D High Performance Marine Engines Engine Design
2003/10/20 An Improved Turbocharger is Used {1052}
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Gear - Remove and Install
2003/10/01 Improved Alternator Drive Assemblies, Auxiliary Drive Pulley Groups and Accessory Drive Groups {1151, 1207, 1425}
C3.3 Industrial Engine Bearing Clearance - Check
2003/10/01 New Seals for the Front Housing {1151, 1207}
3456 Generator Sets Maintenance Interval Schedule - Prime Power Generator Sets
C9 Marine Engines and C9 Marine Generator Sets Electronic Unit Injector Sleeve - Install
3408C, 3412C and 3412D High Performance Marine Engines Fuel System
2013/08/21 Recommendations for Gas Engine Spark Plugs {1550, 1555}
C18 Marine Engines Engine Oil and Filter - Change
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Differential Pressure Switch Circuit - Test
SPP101 Skid Mounted Pumper Safety Messages
SPP101 Skid Mounted Pumper Plate Locations and Film Locations
SPP101 Skid Mounted Pumper Reference Material
3600 Heavy Fuel Engines Refill Capacities and Recommendations
C11 and C13 Engines for Caterpillar Built Machines E390 Fuel Filter Restriction
C9 Marine Engines and C9 Marine Generator Sets Housing (Front) - Remove
C9 Marine Engines and C9 Marine Generator Sets Housing (Front) - Install