Gear Group (Front) - Reverse Rotation
Show/hide table
| |
| Illustration 1 | g03201580 |
|
Front view of engine | |
Show/hide table
| Specification for 8N-5769 Front Gear Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 7N-5279 Adapter As | After installation, bore of 127-5400 Bushing is |
| 2 | 2 | 7N-7539 Thrust Washer | Thickness is |
| 3 | 1 | 116-3242 Idler Gear As | After installation, bore of 116-1365 Bearing is Installation depth of the bearing is |
| 4 | 1 | 7C-3258 Thrust Washer Assembly | Thickness of 7C-3257 Thrust Washer is Protrusion of 7N-2047 Dowel is |
| 5 | 3 | 259-4598 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 6 | 1 | 7C-3259 Shaft | Diameter is |
Show/hide table
| |
| Illustration 2 | g03201581 |
|
Section A-A | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 7 | 2 | 235-3546 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 8 | 1 | 7C-4165 Adapter As | After installation, bore of 127-5400 Bushing is |
| 9 | 1 | 7N-5874 Auxiliary Drive Shaft | Diameter is |
| 10 | 1 | 7N-5245 Pump Adapter | After installation, bore of 127-5400 Bushing is |
| 11 | 1 | 7N-5239 Pump Drive Shaft As | Diameter is Install the 8T-2153 Socket Setscrew to the bottom of the threaded hole and tighten to |
| 12 | 1 | 278-4287 Pump Adapter | After installation, bore of 127-5400 Bushing is During assembly, flush the bushing with the pump adapter surface. Oil hole in the bushing must be aligned with the hole in the bore. |
| 13 | 2 | 7N-5246 Thrust Washer | Thickness is Width of groove in the new pump drive shaft assembly is |
Caterpillar Information System:
3408C, 3412C and 3412D High Performance Marine Engines Electronic Control System Components
2003/10/01 Proper Termination Techniques May Increase Digital Voltage Regulator (DVR) Reliability {4467}
2003/10/01 The Water Resistance of the Wiring Harness Has Improved {1408}
3408C, 3412C and 3412D High Performance Marine Engines General Information
3408C, 3412C and 3412D High Performance Marine Engines Engine Design
2003/10/20 An Improved Turbocharger is Used {1052}
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Gear - Remove and Install
2003/10/01 Improved Alternator Drive Assemblies, Auxiliary Drive Pulley Groups and Accessory Drive Groups {1151, 1207, 1425}
C3.3 Industrial Engine Bearing Clearance - Check
2003/10/01 New Seals for the Front Housing {1151, 1207}
3456 Generator Sets Maintenance Interval Schedule - Prime Power Generator Sets
3456 Generator Sets Maintenance Interval Schedule - Standby Generator Sets
C9 Marine Engines and C9 Marine Generator Sets Electronic Unit Injector Sleeve - Remove
C9 Marine Engines and C9 Marine Generator Sets Electronic Unit Injector Sleeve - Install
3408C, 3412C and 3412D High Performance Marine Engines Fuel System
2013/08/21 Recommendations for Gas Engine Spark Plugs {1550, 1555}
C18 Marine Engines Engine Oil and Filter - Change
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Differential Pressure Switch Circuit - Test
SPP101 Skid Mounted Pumper Safety Messages
SPP101 Skid Mounted Pumper Plate Locations and Film Locations
SPP101 Skid Mounted Pumper Reference Material
3600 Heavy Fuel Engines Refill Capacities and Recommendations
C11 and C13 Engines for Caterpillar Built Machines E390 Fuel Filter Restriction
C9 Marine Engines and C9 Marine Generator Sets Housing (Front) - Remove