Crankshaft Gear - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8H-0663 | Bearing Puller Gp | 1 |
5F-7345 | Screw | 1 | |
126-7183 | Crossblock | 1 | |
126-7181 | Sliding Plate | 2 | |
126-7177 | Puller Leg | 2 |
Start By:
- Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
- Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove ".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove crankshaft gear (1) from crankshaft (3). Remove key (2) from the crankshaft.
Show/hide table
Illustration 1 | g00944168 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Heat the crankshaft gear in an oven to
200 °C (392 °F) . - Install key (2) in crankshaft (3). Install crankshaft gear (1).
Note: The timing marks on the crankshaft gear must be installed toward the front of the crankshaft.
Show/hide table
Illustration 2 | g00944168 |
End By:
- Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install ".
- Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Rocker Arm and Shaft - Remove
C11, C13 and C15 On-highway Engines Engine Speed/Timing Sensor Circuit - Test
3056E Industrial Engine Idler Gear - Remove and Install
G3304B and G3306B Engines Engine Oil Filter Base
3056E Industrial Engine Camshaft Gear - Remove and Install
3126B Marine Engines E096 High Fuel Pressure
C11, C13 and C15 On-highway Engines Cooling Fan Is Always ON
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies User Interface for System Cabinet
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies User Interface for Multiple Module Unit
797 Off-Highway Truck Steering System Machine Preparation for Troubleshooting
3056E Industrial Engine Turbocharger - Install
3056E Industrial Engine Turbocharger - Remove
C7 and C9 On-Highway Engines 0111-14 Low Coolant Level Warning
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0231-02 J1939 Data Incorrect (58)
C9 Marine Auxiliary and Generator Set Engines Engine Oil Sample - Obtain
3126B and 3126E On-highway Engines 0030-08 PTO Throttle signal invalid (29)
3126B and 3126E On-highway Engines 0030-13 PTO Throttle out of calibration (29)
UPS 250 and UPS 300 Uninterruptible Power Supplies Bearing Retainer - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Zinc Rods - Inspect/Replace
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bearing Retainer - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Fuel System Secondary Filter - Replace
C9 Marine Auxiliary and Generator Set Engines Heat Exchanger - Inspect
C7 and C9 On-Highway Engines Transmission (AT/MT/HT) Relay Circuit - Test
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install