Crankcase Breather - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Loosen clamp (1). Remove the clamp and tube (2).
- Loosen clamps (3). Remove both breathers as a unit.
Show/hide table
Illustration 2 g00597465 - Remove O-ring seals (4) from the valve covers. Discard the O-ring seals.
Show/hide table
Illustration 3 g00928366 - Remove two clamps (6). Remove both breathers from hose tee (7).
Inspect the hose tee for cracks. If the tee is cracked, discard the old tee and obtain a new tee for installation.
- Turn the breathers upside-down in order to inspect the condition of the breather elements.
Clean the breather elements with clean, nonflammable solvent. If the breather elements remain contaminated after the cleaning, discard the breathers and obtain new breathers. Do not attempt to disassemble the breathers.
Allow the breather elements to dry before installation.
Show/hide table
Illustration 1 | g00928364 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place clamps (6) over the parts of hose tee (7) that will receive breathers (5). Install the breathers into the tee. Tighten the clamps to
3.0 ± 0.5 N·m (27 ± 4 lb in) .Show/hide tableIllustration 5 g00597465 - Coat new O-ring seals (4) with clean engine oil. Place the O-ring seals on the valve covers.
Show/hide table
Illustration 6 g00928364 - Place clamps (3) around the parts of the breathers that will be attached to the valve covers. Install both breathers as a unit. Tighten the clamps.
- Place clamp (1) on the part of the hose tee that will receive tube (2). Install the tube. Tighten the clamp to
3.0 ± 0.5 N·m (27 ± 4 lb in) .
Show/hide table
Illustration 4 | g00928366 |
Note: Coat the rubber parts with clean engine oil or petroleum jelly in order to make installation easier.
Caterpillar Information System:
3512B Marine Auxiliary Engine Engine Oil and Filter - Change
C9 Urban Transit Bus Engine General Information
G3520C and G3520E Generator Set Engines Exhaust Manifold
2002/10/01 Connecting Rods with Dual Bearing Tab Slots are OK to Use {1218}
2002/10/21 New Electronic Control Modules Used on Machine Engines {1901}
3512B Marine Auxiliary Engine Engine Oil Level - Check
3512B Marine Auxiliary Engine Electronic Control System Operation
C7 and C9 On-Highway Engines 0111-11 Very Low Coolant Level (62)
C7 and C9 On-Highway Engines 0111-04 Coolant Level voltage low (12)
C7 and C9 On-Highway Engines 0111-03 Coolant Level voltage high (12)
C9 On-Highway Engines Lubrication System
3512B Marine Auxiliary Engine Electronic Control System Components
3512B Marine Auxiliary Engine Instrument Panel - Inspect
2002/10/14 New Tightening Procedure for the Base of the Valve Mechanism Cover {1107}
G3500 Engines Finding the Top Center Position for the No. 1 Piston
C7 and C9 On-Highway Engines 0231-14 Transmission Data Link Derate
3512B Marine Auxiliary Engine Configuration Parameters
Product Link 151/201 Electronic Control Module (ECM)
Product Link 151/201 System Components
3054E Industrial Engine Fuel System - Prime
Product Link 151/201 Spare Inputs
Product Link 151/201 General Information
3512B Marine Auxiliary Engine Monitoring System Parameters
3512B Marine Auxiliary Engine Electronic Unit Injector - Inspect/Adjust