Dimensions
Show/hide table
 | |
| Illustration 1 | g00888162 |
Dimensions of the K65-12B Voltage Regulator (A) 212.75 mm (8.376 inch) (B) 190.50 mm (7.500 inch) (C) 161.95 mm (6.376 inch) (D) 139.70 mm (5.500 inch) (E) 19.05 mm (0.750 inch) (F) 75.18 mm (2.960 inch) | |
Description of Terminals
Note: When the voltage regulator is used with a permanent magnet generator, ensure that the jumpers are removed between the following terminals: 20 - 28, 22 - 30 and 24 - 26. Ensure that the jumper is installed between terminals 28 and "GND".
Show/hide table
| Number of the Terminal | Description |
|---|---|
| GND | Ground |
| 2 | Auxiliary input from VAR/PF Controller and/or min/max excitation limiter |
| 3 | Auxiliary input from VAR/PF Controller and/or min/max excitation limiter |
| 4 | This terminal is used in conjunction with terminal 7 for selecting internal voltage adjustment. Place the jumper between terminals 4 and 7 for using internal voltage adjustment. Remote voltage adjustment requires a remote voltage adjust rheostat between terminals 6a and 7. |
| 5 | 1 Ampere Current Transformer (CT) |
| 5a | 5 Ampere Current Transformer (CT) |
| 6 | Common for the Current Transformer |
| 6a | Common connection for selectable features |
| 7 | This terminal is used in conjunction with terminal 4 for selecting external voltage adjustment. Place the jumper between terminals 4 and 7 for using internal voltage adjustment. Remote voltage adjustment requires a remote voltage adjust rheostat between terminals 6a and 7. |
| 8 | Connect terminal 8 to terminal 6a in order to select a 1 V/Hz underfrequency slope. |
| 9 | Connect terminal 9 to terminal 6a in order to select three-phase sensing. |
| 20 | Sensing input on phase C |
| 22 | Sensing input on phase A |
| 24 | Sensing input on phase B |
| 26 | Three-phase power input |
| 28 | Single-phase power input or three-phase power input |
| 30 | Single-phase power input or three-phase power input |
| F1 | Positive field lead |
| F2 | Negative field lead |
Internal Adjustments
Show/hide table
| Adjustment | Description |
|---|---|
| "DRP" | Adjustment of the Voltage Droop |
| "FAC CAL" | This is the factory calibration of the voltage adjustment range. Adjustment by the customer is not required. |
| "VLT ADJ" | Voltage Adjustment |
| "UF" | Underfrequency Knee Adjustment |
| "STB" | Stability Adjustment |
Caterpillar Information System:
C7 and C9 On-Highway Engines Cooling Fan Circuit and A/C High Pressure Switch Circuit - Test
3126B and 3126E On-highway Engines 0111-04 Coolant Level voltage low (12)
PMG3516 Power Module Fuel Metering Valve - Check - Raptor
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Install
3500 Generator Set Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
Electronic Modular Control Panel II (EMCP II) EMCP Electronic Control (Generator Set) - Replace
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Remove
Electronic Modular Control Panel II (EMCP II) EMCP Electronic Control (AC Transformer Box) - Replace
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Electrical Connector - Inspect
Electronic Modular Control Panel II (EMCP II) GSC CID 0268 - FMI 02
2002/05/01 The New 204-8041 Gauge Group Is Available To Measure The Top Ring Groove On Pistons {1214}
Electronic Modular Control Panel II (EMCP II) Display of Voltage or Current is Inaccurate
3054 and 3056 Industrial and Generator Set Engines Engine Oil Filter Base
K65-12B Voltage Regulator Stability - Adjust
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Install
3056E Industrial Engine Crankshaft
3412E, C30 and C32 Marine Engines Connecting Rod Bearings - Remove
K65-12B Voltage Regulator Voltage - Adjust
K65-12B Voltage Regulator Droop - Adjust
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler
330C Excavator Machine System Specifications Recoil Spring
797B Off-Highway Truck Air System Pressure Protection Valve (Air System)
3412E, C30 and C32 Marine Engines Crankshaft - Remove
2007/08/20 C-12/3176C/3196 Front Housing Bolts {1151}