Engine Oil Filter Housings - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7575 | 连杆支架 | 2 |
B | 1U-9824 | 放油工具总成 | 1 |
5N-5566 | 软管 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 卸下机油冷却器和机油温度调节器壳体。
注: 图示未显示以下部件:水温调节器壳体, 连接该壳体的管路, 机油冷却器 和 卸下的机油温度调节器壳体。
- 通过打开排放阀从机油滤清器壳体排放机油。
Show/hide table
图 2 g00869348 - 将起重机和扎带连接至支架 (1)。
- 卸下十个螺栓 (2)。
- 卸下支架。
Show/hide table
图 3 g00869440 - 从滤清器壳体上卸下所有线束夹 (7)。
- 从弯头上卸下传感器 (4)。
- 卸下螺栓 (6) 和卡箍 (9)。
- 卸下螺栓 (3) 和弯头 (5)。 未显示所有螺栓。 如有必要,更换密封垫。
- 卸下螺栓 (10) 和管 (8)。 如有必要,更换密封垫。
Show/hide table
图 4 g00869454 - 卸下线束夹 (13)。
- 拆下管组件 (11)。
注: 电气连接以及模式中的其他变更可能要求在拆卸壳体之前进行更多的拆卸或断开。
- 将起重机和工具 (A) 固定至机油滤清器壳体。 机油滤清器壳体的重量约为
224 kg (496 lb) 。注: 将电气线路移开,以便卸下壳体时,为机油滤清器壳体留出间隙。
- 卸下五个螺栓 (12)。
- 卸下机油滤清器壳体。
Show/hide table
图 1 | g00608730 |
机油滤清器的盖已卸下。 |
注: 如有配备, U-9824 排油工具总成用于排出机油滤清器壳体中的机油。 1U-9823 过滤勺用于从滤清器壳体上卸下机油滤清器滤芯。
Caterpillar Information System:
2002/04/01 New Tools Are Available For Rebuilding The Cylinder Head {1100}
N3 Series Brushless Alternators Regulator - Test
2002/04/01 Two Valve Covers Are Available For Venting Fumes From The Crankcase {1107, 1317}
2002/03/01 A New Service Manual, RENR5901, "Engine Oil Cooler" Is Available {1378}
3406E, C12, C15 and C18 Marine Engines Engine Temperature Sensor Open or Short Circuit - Test
3500 Generator Set Engines Service Meter
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Electrical Connectors and Functions
3500 Generator Set Engines Sending Unit - Water Temperature
3500 Generator Set Engines Sending Unit - Engine Oil Pressure
G3612 and G3616 Engines Fuel Lines - Remove and Install
N3 Series Brushless Alternators Stator - Test
3406E, C12, C15 and C18 Marine Engines Electrical Power Supply Circuit - Test
2002/05/01 Oversized Valve Seat Inserts Are Available {1103}
2002/03/01 The New 201-8114 Exhaust Valve Is Available {1105}
3500 Industrial Engines Tachometer
G3612 and G3616 Engines Engine Oil Filter Housings - Install
3500 Generator Set Engines Tachometer
797B Off-Highway Truck Steering System Steering Cylinder
PMG3516 Power Module Generator Lead Connections
3406E, C12, C15 and C18 Marine Engines Engine Cranks but Will Not Start
N3 Series Brushless Alternators Alternator - Assemble
N3 Series Brushless Alternators Alternator - Disassemble
C15 and C18 Petroleum Generator Sets Generator Start-up Checklist
3508, 3512, and 3516 Generator Sets Bearing - Inspect - Generator