Travel Motor
Show/hide table
Illustration 1 | g00106767 |
Show/hide table
NOTICE |
---|
To prevent damage to the motor, the case must be filled with hydraulic oil at least to the fill port before operation. |
(1) Torque for two stoppers ... 140 ± 14 N·m (105 ± 10 lb ft)
Before assembly, apply a small amount of hydraulic oil on the sliding surfaces of the following parts:
- piston (2)
- guide (3)
- barrel (4)
- piston assembly (9)
- spool (14)
(5) Torque for 10 bolts ... 177 ± 18 N·m (131 ± 13 lb ft)
(6) 107-6981 Shim
- Thickness of one shim ... 0.8 mm (0.032 inch)
-
107-6980 Shim
- Thickness of one shim ... 1.0 mm (0.040 inch)
-
107-6976 Shim
- Thickness of one shim ... 1.2 mm (0.050 inch)
-
107-6977 Shim
- Thickness of one shim ... 1.4 mm (0.055 inch)
-
107-6978 Shim
- Thickness of one shim ... 1.6 mm (0.063 inch)
-
107-6979 Shim
- Thickness of one shim ... 1.8 mm (0.071 inch)
To ensure that the following conditions are fulfilled, install shims (6) :
- When parking brake release port (12) is vented to the air, the motor output shaft does not rotate with a torque of 785 N·m (580 lb ft) or less.
- When pressure at parking brake release port (12) is 780 kPa (115 psi), the motor output shaft rotates with a torque of 29 N·m (21 lb ft) or less. Both the inlet port and the outlet port must be open to the hydraulic tank.
(7) Apply 5P-3413 Sealant to the seal.
(8) 095-7380 Spring
- Free length ... 15.0 mm (0.59 inch)
- Outside diameter ... 11.7 mm (0.46 inch)
- Inside diameter ... 8.9 ± 0.10 mm (0.35 ± 0.004 inch)
- Outside diameter ... 11.7 mm (0.46 inch)
(10) 118-4057 Spring
- Free length ... 35.9 mm (1.4 inch)
- Outside diameter ... 9.5 ± 0.2 mm (0.37 ± 0.008 inch)
- Inside diameter ... 4.9 mm (0.19 inch)
- Outside diameter ... 9.5 ± 0.2 mm (0.37 ± 0.008 inch)
(11) Torque for plugs ... 14.7 ± 1.5 N·m (11 ± 1 lb ft)
(13) 096-3978 Spring
- Free length ... 34.7 mm (1.37 inch)
- Outside diameter ... 14.0 ± 0.1 mm (.55 ± .004 inch)
- Inside diameter ... 10.4 mm (0.41 inch)
- Outside diameter ... 14.0 ± 0.1 mm (.55 ± .004 inch)
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swing Gear and Bearing - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Assemble
2002/01/01 A New Extension Assembly Is Available For The Spark Plugs {1550}
Air/Fuel Ratio Control (Oxygen Feedback) System Setup Procedure
Monitors For 3600 Diesel Monitoring Systems Mounting
3126 Truck Engine Military Water Temperature Regulator Housing - Remove and Install
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Speed Control
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Disassemble
2002/10/01 The New 211-4359 Engine Oil Filter is Now Available for Compact Installations {1308}
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Remove
C-10 and C-12 Engines Engine Control Module - Remove and Install
Monitors For 3600 Diesel Monitoring Systems Dimensions
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor
C7 On-highway Engine Fuel Transfer Pump - Install
Monitors For 3600 Diesel Monitoring Systems Connections
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swing Gear and Bearing - Install
3054, 3054B and 3056 Marine Engines Piston Cooling Jet
3126E On-highway Engine Unit Injector Hydraulic Pump - Install
CPT372 Truck Mounted Pumper Drive Shaft Universal Joints - Lubricate
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Remove
3126E On-highway Engine Customer Specified Parameters Table
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Disassemble
320C Material Handler Machine System Specifications Travel Counterbalance Valve