Swing Gear and Bearing - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 138-7574     | Link Bracket     | 4     |
(B)     | 132-8223     | Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase) (1)     | 1     |
1U-6221 | Hydraulic Torque Wrench     | 1     | |
132-8143 | 36 mm Hex Link     | 1     |
Show/hide table
( 1 ) | 132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available. |
Start By:
- Remove the undercarriage frame. Refer to the manufacturer's Disassembly and Assembly Manual for the removal of the undercarriage frame.
- Remove all of the grease from the swing gear and bearing. Put the grease in a suitable container for storage or disposal.
- Put an alignment mark on swing gear and bearing (1) and on the undercarriage frame assembly for assembly purposes. Attach Tooling (A) to swing gear and bearing (1), as shown. Attach a suitable lifting device to Tooling (A). Apply slight lifting tension to the swing gear and bearing.
Show/hide table
Illustration 1 | g00520664 |
- Use Tooling (B) to remove bolts (2) and the spacers that hold swing gear and bearing (1) to the undercarriage frame.
Show/hide table
Illustration 2 | g00520670 |
- Remove the swing gear and bearing. The weight of the swing gear and bearing is approximately 363 kg (800 lb).
- Remove inner dust seal (3) and outer dust seal (4) from the swing gear and bearing.
Show/hide table
Illustration 3 | g00721855 |
Note: Inner dust seal (3) and outer dust seal (4) may have been installed dry in the swing gear and bearing or inner dust seal (3) and outer dust seal (4) may have been bonded to the swing gear and bearing.
- Clean the sealing grooves of the inner dust seal and the sealing grooves of the outer dust seal with a fine grit sandpaper. Use a cleaning solvent to clean the sealing grooves. Make sure that the seal grooves are thoroughly clean and dry prior to installing the new dust seals.
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Assemble
2002/01/01 A New Extension Assembly Is Available For The Spark Plugs {1550}
Air/Fuel Ratio Control (Oxygen Feedback) System Setup Procedure
Monitors For 3600 Diesel Monitoring Systems Mounting
3126 Truck Engine Military Water Temperature Regulator Housing - Remove and Install
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Speed Control
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Disassemble
2002/10/01 The New 211-4359 Engine Oil Filter is Now Available for Compact Installations {1308}
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor - Remove
C-10 and C-12 Engines Engine Control Module - Remove and Install
Monitors For 3600 Diesel Monitoring Systems Dimensions
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Brake Valve - Install
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Motor
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor
C7 On-highway Engine Fuel Transfer Pump - Install
Monitors For 3600 Diesel Monitoring Systems Connections
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swing Gear and Bearing - Install
3054, 3054B and 3056 Marine Engines Piston Cooling Jet
3126E On-highway Engine Unit Injector Hydraulic Pump - Install
CPT372 Truck Mounted Pumper Drive Shaft Universal Joints - Lubricate
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Remove
3126E On-highway Engine Customer Specified Parameters Table
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Swivel - Disassemble