Swing Motor - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-2674(1) | Vacuum Cap | 1 |
| B | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
| (1) | Add a |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the area around the swing motor and the swing drive. Thoroughly clean the mating surfaces of the swing motor and the swing drive.
Show/hide table
Illustration 1 g01593356 - Use a suitable lifting device to position swing motor (16) in the machine. The weight of swing motor (16) is approximately
43 kg (94 lb) . - Install bolts (17). Tighten bolts (17) to a torque of
90 ± 2 N·m (67 ± 2 lb ft) .Show/hide table
Illustration 2 g01593355 - Install all hose assemblies (15) to the swing motor.
Show/hide table
Illustration 3 g01571093 - Remove Tooling (A) from the hydraulic tank. Install the cap on the hydraulic tank.
Show/hide table
Illustration 4 g01593357 - Close storage box (14) for the window guards.
Show/hide table
Illustration 5 g01593354 - Install panel (13).
Show/hide table
Illustration 6 g01593353 - Install panel (12).
Show/hide table
Illustration 7 g01593133 Show/hide table
Illustration 8 g01593307 - Position the refrigerant condenser and refrigerant dryer (8) as a unit. Install bolts (10). Connect clips (11) and (9).
- Install top mounting bolts (7). Repeat for the three bottom mounting bolts.
Show/hide table
Illustration 9 g01593305 - Install panel (6).
Show/hide table
Illustration 10 g01593299 - Connect clip (5). Connect harness assembly (4) to refrigerant condenser (3).
Show/hide table
Illustration 11 g01589881 - Close housing (2) for the refrigerant condenser. Close engine hood (1).
- Check the hydraulic oil level. Refer to Operation and Maintenance, "Hydraulic System Oil Level - Check" and Operation and Maintenance, "Capacities (Refill)".
Caterpillar Information System:
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Electronic Control Module (ECM) - Replace
345C and W345C Excavators and 345C MHPU Mobile Hydraulic Power Unit Machine Electronic Control System Electronic Control Module (ECM) - Replace
M316D, M318D and M322D Wheeled Excavators Machine Systems Boom - Install - Standard Boom
2008/09/22 Improved Material is Now Used on Hose Assemblies that Are for the Engine Oil Filter for Certain Mini Hydraulic Excavators {1306, 1307, 1308}
Low or Erratic Hydraulic Power is Experienced on Certain Wheeled Excavators{5455} Low or Erratic Hydraulic Power is Experienced on Certain Wheeled Excavators{5455}
314D CR Hydraulic Excavator Machine Systems Swing Motor - Remove
2008/06/30 Installation Procedure for the Fuel Transfer Kit on the Hydraulic Electronic Unit Injector (HEUI) Pump {1256}
Temporary Weld Repair for Crack in Lower Jaw of Shear{6349} Temporary Weld Repair for Crack in Lower Jaw of Shear{6349}
2008/07/14 Correction to the Parts Manual , "Filter Gp-Fuel" for Excavators {1261}
320D Excavator Mirror - If Equipped
314D CR Hydraulic Excavator Machine Systems Speed Control - Remove and Install
314D CR Hydraulic Excavator Machine Systems Pressure Switch (Refrigerant Pressure Cutoff) - Remove and Install
323D MHPU Mobile Hydraulic Power Unit Machine System Specifications Fuel Tank
385C Excavator and 385C Front Shovel Machine System Specifications Accumulator (Pilot)
330B Excavator Machine System Specifications Flow Control Valve
2008/08/11 New Software For the Engine ECM is Now Available {1901, 7600, 7620}
2008/07/14 Updated Electronic Unit Injectors {1290, 1901}
314D CR Hydraulic Excavator C4.2 Engine Supplement Refrigerant Compressor - Remove and Install
2008/09/01 The Pump Control Valve Has Been Improved on Certain Mini Hydraulic Excavators {5455}
314D CR Hydraulic Excavator Machine Systems Pilot Valve (Joystick) - Remove - Right Hand
Procedure for Replacing the Pump Control Valve on Certain Mini Hydraulic Excavators{5455} Procedure for Replacing the Pump Control Valve on Certain Mini Hydraulic Excavators{5455}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Pilot Valve (Boom Drift Reduction)
319D Excavator Machine System Specifications Pilot Valve (Travel)
314D CR Hydraulic Excavator Machine Systems Pilot Valve (Joystick) - Install - Right Hand