Hydraulic Tank Screen - Clean
Show/hide table
 | |
| Illustration 1 | g01132442 |
- Park the machine on level ground.
- Unlatch the engine hood and raise the engine hood.
- Remove bolts (1), washers (2) and cover (3) from the top of the hydraulic tank.
Show/hide table
 | |
| Illustration 2 | g00687272 |
(1) Bolts (2) Washers (3) Cover | |
- Clean the area thoroughly in order to keep dirt out of the screen cover. Clean the area thoroughly in order to keep dirt out of the fill/vent plug.
Show/hide table
 | |
| Illustration 3 | g00687312 |
- Relieve the internal pressure from the hydraulic tank by loosening the fill/vent plug. After the pressure is relieved, remove the fill/vent plug.
- Remove bolts (4), washers (5) and cover (6) .
Show/hide table
 | |
| Illustration 4 | g00691202 |
(4) Bolts (5) Washers (6) Cover (7) Spring (8) Screen | |
- Remove spring (7) and screen (8) .
Note: Refer to Operation and Maintenance, "General Hazard Information" for information on containing fluid spillage.
Note: Do not allow spring (7) to fall into the tank.
- Wash the screen in a clean nonflammable solvent. Allow the screen to dry. Inspect the screen. Replace the screen, if the screen is damaged.
- Remove O-ring seal (9) from screen (12) .
Show/hide table
 | |
| Illustration 5 | g00691204 |
(9) O-ring seal (10) O-ring seal | |
- Inspect O-ring seals (9) and (10). Replace the O-ring seals if wear or damage is evident.
- Install O-ring seal (9) on screen (12) .
- Install screen (8) and spring (7). Then install cover (6), washers (5), and bolts (4) .
Note: Make sure that the O-ring seals and the spring are properly positioned during installation.
- Inspect the O-ring seal on the filler plug for damage. Replace the O-ring, if necessary. Clean the filler plug. Install the filler plug.
- Install cover (3) with bolts (1) and washers (2) .
- Close the engine hood and latch the engine hood.
Caterpillar Information System:
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil Level - Check
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil Filter (Pilot) - Replace
M315D2 and M317D2 Excavators Automatic Lubrication Grease Tank - Fill - If Equipped
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil Filter (Case Drain) - Replace
330D Forest Machine Machine Systems Load Control Valve (Boom Cylinder) - Remove
568 Forest Machines Machine Systems Load Control Valve (Stick Cylinder) - Install
365C MHPU Mobile Hydraulic Power Unit Hydraulic System Accumulator (Pilot) - Test and Charge
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil - Change
365C MHPU Mobile Hydraulic Power Unit Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
A Procedure to Remove the Check Valve on Certain Field Installed Quick Coupler Lines Groups{5057, 6129, 7000} A Procedure to Remove the Check Valve on Certain Field Installed Quick Coupler Lines Groups{5057, 6129, 7000}
568 Forest Machines Machine Systems Load Control Valve (Stick Cylinder) - Remove
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
C4.2 and C6.4 Engines for Caterpillar Built Machines Cooling System
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
321D LCR Excavator Lifting Capacities
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel System - Prime
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Compression - Test
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
2007/06/18 A New Idler Pulley Is Available for the Engine Pulley Group {1361}
2007/04/16 New Software for the Auxiliary Hydraulic Circuits Is Available {7610, 7620}
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M316D Excavator with a Offset Boom (Heavy Lift Option)
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Oil Pressure - Test