Hydraulic System Oil Filter (Pilot) - Replace
Show/hide table
Illustration 1 | g01132442 |
- Move the lever for the hydraulic lockout control to the UNLOCKED position.
Show/hide table
Illustration 2 | g00811329 |
- Turn the engine start switch to the ON position.
- Move the joysticks and the travel levers/pedals to the full stroke positions in order to relieve the pressure in the pilot lines.
- Turn the engine start switch to the OFF position and return the lever for the hydraulic lockout control to the LOCKED position.
- Slowly loosen the fill/vent plug on top of the hydraulic tank in order to relieve the internal pressure of the hydraulic tank.
Show/hide table
Illustration 3 | g00687449 |
- After the pressure is relieved, tighten the fill/vent plug.
- Open the access door on the right side of the machine.
Show/hide table
Illustration 4 | g01357044 |
- Clean the area in order to keep dirt out of the filter base.
Show/hide table
Illustration 5 | g00687480 |
- Remove the used pilot filter element from the filter base.
Note: This element is a cartridge type filter. The element cannot be reused.
Note: Used filters should always be disposed of according to local regulations.
- Clean the filter base.
- Coat the seal of a new pilot filter with clean hydraulic oil. Install the new pilot filter in the filter base. Tighten the pilot filter hand tight.
Show/hide table
Illustration 6 | g00101502 |
Caterpillar Information System:
M315D2 and M317D2 Excavators Automatic Lubrication Grease Tank - Fill - If Equipped
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil Filter (Case Drain) - Replace
330D Forest Machine Machine Systems Load Control Valve (Boom Cylinder) - Remove
568 Forest Machines Machine Systems Load Control Valve (Stick Cylinder) - Install
365C MHPU Mobile Hydraulic Power Unit Hydraulic System Accumulator (Pilot) - Test and Charge
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil - Change
365C MHPU Mobile Hydraulic Power Unit Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
A Procedure to Remove the Check Valve on Certain Field Installed Quick Coupler Lines Groups{5057, 6129, 7000} A Procedure to Remove the Check Valve on Certain Field Installed Quick Coupler Lines Groups{5057, 6129, 7000}
568 Forest Machines Machine Systems Load Control Valve (Stick Cylinder) - Remove
330D Excavator Forest Machine C9 Engine Supplement Engine Rear Mount - Install
330D and 336D Excavators Hydraulic System Relief Valve (Line) - Test and Adjust
325C MHPU Mobile Hydraulic Power Unit Hydraulic System Oil Level - Check
325C MHPU Mobile Hydraulic Power Unit Hydraulic Tank Screen - Clean
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
C4.2 and C6.4 Engines for Caterpillar Built Machines Cooling System
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
321D LCR Excavator Lifting Capacities
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel System - Prime
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Compression - Test
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
2007/06/18 A New Idler Pulley Is Available for the Engine Pulley Group {1361}
2007/04/16 New Software for the Auxiliary Hydraulic Circuits Is Available {7610, 7620}