Stick Cylinder
Show/hide table
| |
| Illustration 1 | g02769936 |
Show/hide table
| Specification for 242-6765 Stick Cylinder Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | During press fit, insert the bushing in the cap assembly and rod assembly with the tapered side first. | ||
| 2 | 241-7381 Bushing | Bore diameter before installation is Installation depth of the bushing in the cap assembly is Installation depth of the bushing in the rod assembly is |
|
| 2 | 1 | 123-2060 Locknut | Before assembly, lubricate the face and the threads with 309-6932 Hydraulic Oil.
Torque to |
| 3 | 2 | 158-9065 Ring | Lubricate the inside diameter and the outside diameter with clean grease. |
| 4 | 1 | 9X-3598 Seal As | Lubricate the inside diameter and the outside diameter of the seal assembly with clean grease. |
| 5 | 1 | 179-9667 Ring | Lubricate the inside diameter and the outside diameter with clean grease. |
| A | 1 | 247-8742 Cylinder As | Diameter is |
| B | 1 | 247-8745 Rod As | Diameter is |
| C | 1 | 087-5434 Head | Bore of the head over two lands is |
| 6 | 1 | 103-8380 Stop | Free linear movement of stop after assembly is |
| 7 | 2 | 095-0929 Retaining Ring | Maximum outside diameter of two retaining rings after assembly is |
| 8 | 1 | 247-8791 Seal Ring | The slit of the seal ring must turn in the direction of the piston. |
| 9 | 1 | 114-0757 Bushing | Outside diameter is Thickness is |
| 10 | 1 | 170-9847 Buffer Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. |
| 11 | 1 | 216-0005 U-Cup Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. |
| 12 | 1 | 165-9289 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. |
| 13 | - | - | Before assembly, apply green Loctite 609 to the wiper seal groove. |
Caterpillar Information System:
320D and 323D Excavators Machine System Specifications Boom Cylinder
Fast Fill System-Fuel {1273, 1279, 1710} Fast Fill System-Fuel {1273, 1279, 1710}
C27 and C32 Engines for Caterpillar Built Machines CID 1785 FMI 10 Intake Manifold Pressure Signal abnormal rate of change
325D and 329D Excavators and 325D Material Handler Machine System Specifications Recoil Spring
3064 and 3066 Engines for Caterpillar Built Machines Exhaust Manifold
330D, 336D and 340D Excavators Hydraulic System Hydraulic Oil Cooler
330B Excavator Machine System Specifications Front Idler
C6.6 Engines for Caterpillar Built Machines Starter Motor
C15 Engine for the 657G Wheel Tractor-Scraper Ether Injection System - Test
M325D and M330D Excavators Power Train Electronic Control System Electronic Control Module (ECM) - Configure
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Head - 3066
M325D and M330D Excavators Power Train Electronic Control System Calibration
2006/01/30 Installation Instructions for the Grease Fittings on Hydraulic Hammers {6333}
C11 and C13 Engines Engine Oil Pressure Sensor
2006/01/23 Proper Identification of Ports on 5P-0306 Vacuum Transducer {0768, 5050, 5056}
2006/02/13 Disposable Dessicant Filter is Now Available {0618, 0646}
Squeal which is Caused by the Pressure Relief Valve on 301.6C, 301.8C and 302.5C Mini Hydraulic Excavators{5057, 5264} Squeal which is Caused by the Pressure Relief Valve on 301.6C, 301.8C and 302.5C Mini Hydraulic Excavators{5057, 5264}
2006/04/24 A Conical Bumper Has Been Added for the Alignment of the Rear Hood on Mini Hydraulic Excavators {1051, 7251}
2006/01/30 Improved Air Conditioning Circulation on Excavator {7251, 7276}
303.5C and 303C Mini Hydraulic Excavators Machine Systems Pilot Valve (Boom Swing) - Disassemble
303.5C and 303C Mini Hydraulic Excavators Machine Systems Pilot Valve (Boom Swing) - Assemble
Installation of the 225-4256 Film {7405, 7557} Installation of the 225-4256 Film {7405, 7557}
C15 Engine for the 657G Wheel Tractor-Scraper Event Codes
2006/03/27 Relocation of the Quick Disconnect Connector's on the Excavator Stick {1329, 5057}