Water Temperature Regulator - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
在工作温度下,发动机冷却液是热的,并且带有压力。 蒸汽还会引起人身伤害。 只有在发动机已关闭且加注口盖冷却到可徒手触摸后,才能检查冷却液液位。 缓慢卸下加注口盖,释放其中压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触,以防造成人身伤害。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将发动机冷却液排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "加注容量"。
- 打开发动机罩。
- 断开软管 (1) 和 (4) 。
Show/hide table
图 1 | g01182446 |
- 拆下螺栓 (2) 、水温调节器壳体 (3) 和密封垫。
- 将壳体 (5) 从壳体 (6) 上分离
Show/hide table
图 2 | g01182447 |
- 拆下密封垫 (8) 、水温调节器 (7) 和密封。
Show/hide table
图 3 | g01182448 |
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装密封、水温调节器 (7) 和密封垫 (8) 。
Show/hide table
图 4 | g01182448 |
- 将壳体 (5) 连接到壳体 (6) 上。
Show/hide table
图 5 | g01182447 |
- 连接软管 (1) 和 (4) 。
Show/hide table
图 6 | g01182446 |
- 安装水温调节器壳体 (3) 、密封垫和螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 50 ± 10 N·m (37 ± 7 lb ft)。
- 关闭发动机罩。
- 为发动机加注冷却液。 请参阅操作和保养手册, "加注容量"。
Caterpillar Information System:
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swing Drive - Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swing Drive - Remove
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Bucket Cylinder - Remove and Install
Installation of Replacement Switches for the Travel Alarm on Mini Hydraulic Excavators{7429} Installation of Replacement Switches for the Travel Alarm on Mini Hydraulic Excavators{7429}
303.5C CR and 303C CR Mini Hydraulic Excavators Hydraulic System Travel Counterbalance Valve
365C Excavator Engine Supplement Engine Oil Filter Base - Install
365C Excavator Engine Supplement Engine Oil Filter Base - Remove
C7.1 (Mech) Industrial Engine Gear Group (Front)
C7.1 (Mech) Industrial Engine Oil Pump
C9 Generator Set Engine Crankcase Breather - Clean
C7.1 Engines for Caterpillar Built Machines Front Housing and Covers
365C Excavator Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
325C Excavator Engine Supplement Fan - Remove and Install
365C Excavator Engine Supplement Ether Start Valve - Remove and Install
302.5C Mini Hydraulic Excavator Machine Systems Swing Boom Cylinder - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Hydraulic System Travel Counterbalance Valve
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Bucket Linkage - Remove and Install
365C Excavator Engine Supplement Engine Electronic Control - Remove and Install
365C Excavator Engine Supplement Fuel Cooler - Remove and Install
365C Excavator Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
365C Excavator Engine Supplement Fuel Priming Pump - Remove and Install
365C Excavator Engine Supplement Fuel Transfer Pump - Remove and Install
C6.6 Engines for Caterpillar Built Machines Crankshaft
314E Excavator Machine System Specifications Check Valve (Return Lines)