Fuel Cooler - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 卸下螺栓 (1) 和防护罩 (2) 。
Show/hide table
图 1 | g01182583 |
- 关闭燃油切断阀 (3) 。
Show/hide table
图 2 | g01182584 |
- 拆下螺栓 (4) 后打开门 (5) 。
Show/hide table
图 3 | g01182585 |
- 断开软管组件 (8) 和 (9) 。 拆下螺栓 (6) 和燃油冷却器 (7) 。
Show/hide table
图 4 | g01182586 |
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 定位燃油冷却器 (7) 后安装螺栓 (6) 。
Show/hide table
图 5 | g01182586 |
- 连接软管组件 (8) 和 (9) 。
- 关闭门 (5) 后安装螺栓 (4) 。
Show/hide table
图 6 | g01182585 |
- 打开燃油切断阀 (3) 。
Show/hide table
图 7 | g01182584 |
- 安装防护罩 (2) 和螺栓 (1) 。
Show/hide table
图 8 | g01182583 |
Caterpillar Information System:
365C Excavator Engine Supplement Engine Electronic Control - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Bucket Linkage - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Hydraulic System Travel Counterbalance Valve
302.5C Mini Hydraulic Excavator Machine Systems Swing Boom Cylinder - Remove and Install
365C Excavator Engine Supplement Ether Start Valve - Remove and Install
325C Excavator Engine Supplement Fan - Remove and Install
365C Excavator Engine Supplement Water Temperature Regulator - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swing Drive - Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swing Drive - Remove
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Bucket Cylinder - Remove and Install
Installation of Replacement Switches for the Travel Alarm on Mini Hydraulic Excavators{7429} Installation of Replacement Switches for the Travel Alarm on Mini Hydraulic Excavators{7429}
303.5C CR and 303C CR Mini Hydraulic Excavators Hydraulic System Travel Counterbalance Valve
365C Excavator Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
365C Excavator Engine Supplement Fuel Priming Pump - Remove and Install
365C Excavator Engine Supplement Fuel Transfer Pump - Remove and Install
C6.6 Engines for Caterpillar Built Machines Crankshaft
314E Excavator Machine System Specifications Check Valve (Return Lines)
2005/07/04 New Software Reduces the Trip Points on the Fuel Pressure Sensor {1718, 7620}
320D Excavator Specifications
2005/07/04 An Improved Idler Pulley Has Been Released {1358}
365C Excavator Engine Supplement Fuel Filter and Water Separator Base - Remove and Install - Primary
365C Excavator Engine Supplement Crankshaft Vibration Damper and Pulley - Remove and Install
365C Excavator Engine Supplement Oil Pan - Install
365C Excavator Engine Supplement Oil Pan - Remove