Removal Procedure
Show/hide table
Table 1
| Required Tools |
| Tool |
Part Number |
Part Description |
Qty |
| A |
138-7573 |
Link Bracket |
2 |
Start By:
- Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove and Install".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Show/hide table
|
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
|
Show/hide table
|
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
|
Show/hide table
 |
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
 |
Show/hide table
|
 |
|
| Illustration 1 | g01181698 |
- Remove the top bracket and bottom bracket (2). Disconnect elbow (1) and reposition elbow (1). Remove screen (3) and disconnect hose assembly (4), that is not shown.
Show/hide table
|
 |
|
| Illustration 2 | g01181701 |
- Remove bracket (5) and bolts (6) .
Show/hide table
|
 |
|
| Illustration 3 | g01181702 |
- Loosen bolts (7) .
Show/hide table
|
 |
|
| Illustration 4 | g01181703 |
- Install Tooling (A) and a suitable lifting device. Remove bottom bolts (7) and remove hydraulic oil cooler (8) from the machine. The weight of hydraulic oil cooler (8) is approximately 39 kg (85 lb).
Installation Procedure
Show/hide table
Table 2
| Required Tools |
| Tool |
Part Number |
Part Description |
Qty |
| A |
138-7573 |
Link Bracket |
2 |
Show/hide table
|
| |
|
| Illustration 5 | g01181703 |
Show/hide table
|
| |
|
| Illustration 6 | g01181702 |
- Install Tooling (A) and a suitable lifting device onto hydraulic oil cooler (8). Place bolts (7) into the bottom holes on hydraulic oil cooler (8) and place hydraulic oil cooler (8) into position on the machine. The weight of hydraulic oil cooler (8) is approximately 39 kg (85 lb).
Show/hide table
|
| |
|
| Illustration 7 | g01181702 |
- Tighten bolts (7) .
Show/hide table
|
| |
|
| Illustration 8 | g01181701 |
- Install side bolts (6) and install bracket (5) .
Show/hide table
|
| |
|
| Illustration 9 | g01181698 |
- Connect hose assembly (4), that is not shown. Position screen (3) and install the screen to the hydraulic oil cooler. Position elbow (1) and connect elbow (1) to the hydraulic oil cooler. Install the top bracket and bottom bracket (2) .
End By:
Install the aftercooler. Refer to Disassembly and Assembly, "After Cooler - Remove and Install".
