301.6C, 301.8C and 302.5C Mini Hydraulic Excavators Caterpillar


Lifting Capacities

Usage:

302.5C GBB

------ WARNING! ------

Failure to comply to the rated load can cause possible personal injury or property damage. Review the rated load of a particular work tool before performing any operation. Make adjustments to the rated load as necessary for non-standard configurations.


Note: Rated loads are based upon a standard machine with the following conditions:

  • lubricants

  • full fuel tank

  • cab

  • 75 kg (165 lb) operator

Rated loads will vary with different work tools. Consult your Caterpillar dealer regarding the rated load for specific work tools.

Note: Rated loads should be used as a guide. Work tools, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on rated loads. The operator is responsible for being aware of these effects.

Special hazards (toxic gases, ground conditions, etc) require special precautions. The operator must determine whether special hazards exist in each application. The operator shall perform the appropriate steps in order to eliminate the hazard. The operator shall perform the appropriate steps in order to reduce the hazard.

For North American applications, the rated operating load is defined by " SAE J1097 1988". For European applications, the rated operating load is defined by "ISO 10567 1992". The rated operating load is defined as the lower value of 75% of the static tipping capacity or 87% of the hydraulic lift capacity.

The rated loads for the 301.6C were calculated with a machine that was equipped with a 400 mm (15.75 inch) bucket. The standard stick is 890 mm (35 inch) long. The long stick is 1090 mm (43 inch) long.

The rated loads for the 301.8C were calculated with a machine that was equipped with a 400 mm (15.75 inch) bucket. The undercarriage and the dozer blade of the 301.8 was expanded. The standard stick is 890 mm (35 inch) long. The long stick is 1090 mm (43 inch) long.

The rated loads for the 302.5C were calculated with a machine that was equipped with a 400 mm (15.75 inch) bucket. The standard stick is 1110 mm (43.7 inch) long. The long stick is 1400 mm (55 inch) long.

Note: In European countries, regulations require a load sensing indicator and a boom lowering control device if more than 1000 kg (2200 lb) is lifted during object handling applications. Regulations also require a load sensing indicator and a boom lowering control device if a force that is greater than 40000 N·m (29500 lb ft) is created during object handling applications. Even if the hydraulic lift capacity is capable, do not exceed a load of 1000 kg (2200 lb). Do not exceed a force of 40000 N·m (29500 lb ft) in European object handling applications.

Note: European regulations require the machine to be equipped with a mechanism that locks the dozer blade into position if the dozer blade is used to increase stability. If a mechanism that locks the dozer blade into position is not installed, use the values that are given in the tables for the machine when the blade is up. If a mechanism that locks the dozer blade into position is installed, use the values that are given in the tables for the machine when the blade is down.



Illustration 1g01055537
(H) Height
(F) Lifting capacity over the front of the machine
(S) Lifting capacity over the side of the machine
(R) Reach

301.6C

Table 1
301.6C Lifting Capacities with a Standard Stick and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              332(1)  253      335(1)  241  2.57 
2.0 m              341(1)  250      298  193  2.90 
1.5 m          450(1)  344  375  243  279  179  263  168  3.11 
1.0 m          512  322  364  232  274  175  246  156  3.21 
0.5 m          491  303  353  222  269  170  242  152  3.21 
0      762(1)  444  480  294  345  216  265  166  250  157  3.12 
-0.5 m  833(1)  833(1)  767  447  478  292  343  214      276  173  2.91 
-1.0 m  937(1)  892  776  454  483  296  346  217      336  211  2.55 
-1.5 m      599(1)  469              424(1)  322  1.94 
(1) Limited by the hydraulic capacity rather than tipping load

Table 2
301.6C Lifting Capacities with a Standard Stick and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              732(1)  558      739(1)   531  8.43 
6.6 ft              752(1)  551      656  426  9.51 
4.9 ft          992(1)  759  827  536  615  395  580  370  10.20 
3.3 ft          1129  710  803  512  604  386  542  344  10.53 
1.6 ft          1083  668  778  490  593  375  534  335  10.53 
0      1680(1)  979  1058  648  761  476  584  366  551  346  10.24 
-1.6 ft  1836(1)  1836(1)  1691  985  1053  643  756  471      608  381  9.55 
-3.3 ft  2065(1)  1966  1710  1000  1064  652  762  478      740  465  8.37 
-4.9 ft      1320(1)  1033              934(1)  709  6.36 
(1) Limited by the hydraulic capacity rather than tipping load

Table 3
301.6C Lifting Capacities with a Standard Stick and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5m   2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              332(1)  277      335(1)  265  2.57 
2.0 m              341(1)  275      342(1)  213  2.90 
1.5 m          450(1)  378  385(1)  267  354(1)  198  351(1)  186  3.11 
1.0 m          596(1)  356  449(1)  257  380(1)  193  362(1)  173  3.21 
0.5 m          711(1)  337  507(1)  246  405(1)  188  375(1)  169  3.21 
0      762(1)  497  752(1)  327  537(1)  240  415(1)  184  392(1)  175  3.12 
-0.5 m  833(1)  833(1)  877(1)  500  724(1)  325  524(1)  237      409(1)  192  2.91 
-1.0 m  937(1)  937(1)  824(1)  508  629(1)  329  445(1)  241      426(1)  234  2.55 
-1.5 m      599(1)  524              424(1)  357  1.94 
(1) Limited by the hydraulic capacity rather than tipping load

Table 4
301.6C Lifting Capacities with a Standard Stick and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              731(1)  610      738(1)  584  8.43 
6.6 ft              751(1)   606      753(1)   469  9.51 
4.9 ft          992(1)   833  848(1)   588  780(1)   436  773(1)   410  10.20 
3.3 ft          1313(1)   784  989(1)   566  837(1)   425  798(1)   381  10.53 
1.6 ft          1567(1)   743  1117(1)   542  892(1)   414  826(1)   372  10.53 
0      1679(1)   1095  1657(1)   720  1183(1)   529  914(1)   405  864(1)   385  10.24 
-1.6 ft  1836(1)   1836(1)   1933(1)   1102  1596(1)   716  1155(1)   522      901(1)   423  9.55 
-3.3 ft  2065(1)   2065(1)   1816(1)   1119  1386(1)   725  981(1)   531      939(1)   515  8.37 
-4.9 ft      1320(1)   1155              934(1)   787  6.36 
(1) Limited by the hydraulic capacity rather than tipping load

Table 5
301.6C Lifting Capacities with a Long Stick and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              284(1)  257      303(1)  211  2.81 
2.0 m              298(1)  256  287  187  269  175  3.12 
1.5 m              346(1)  248  284  184  241  154  3.30 
1.0 m      832  500  522  331  369  237  278  178  227  144  3.40 
0.5 m      648(1)  457  498  310  357  226  271  172  223  140  3.40 
0  395(1)  395(1)  765  445  484  297  348  218  266  167  230  144  3.31 
-0.5 m  706(1)  706(1)  764  444  478  293  343  214  264  165  249  156  3.12 
-1.0 m  1054(1)  879  771  450  480  294  344  214      293  183  2.80 
-1.5 m  959(1)  901  761(1)  461  489  302          402  252  2.28 
(1) Limited by the hydraulic capacity rather than tipping load

Table 6
301.6C Lifting Capacities with a Long Stick and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              626(1)  566      668(1)  465  9.22 
6.6 ft              656(1)  564  632  412  593  385  10.24 
4.9 ft              762(1)  546  626  405  531  339  10.83 
3.3 ft      1834  1102  1150  729  813  522  612  392  500  317  11.15 
1.6 ft      1428(1)  1007  1097  683  787  498  597  379  491  308  11.15 
0  870(1)  870(1)  1686  981  1067  654  767  480  586  368  507  317  10.86 
-1.6 ft  1556(1)  1556(1)  1684  978  1053  645  756  471  582  363  548  343  10.24 
-3.3 ft  2323(1)  1937  1699  992  1058  648  758  471      645  403  9.19 
-4.9 ft  2114(1)  1986  1677(1)  1016  1078  665          886  555  7.48 
(1) Limited by the hydraulic capacity rather than tipping load

Table 7
301.6C Lifting Capacities with a Long Stick and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              284(1)  284      303(1)  231  2.81 
2.0 m              298(1)  281  309(1)  205  311(1)  192  3.12 
1.5 m              346(1)  273  326(1)  202  321(1)  171  3.30 
1.0 m      868(1)  555  535(1)  365  416(1)  262  358(1)  197  332(1)  159  3.40 
0.5 m      648(1)  510  673(1)  343  485(1)  250  392(1)  190  345(1)  156  3.40 
0  395(1)  395(1)  769(1)  498  744(1)  330  529(1)  242  413(1)  186  361(1)  160  3.31 
-0.5 m  706(1)  706(1)  980(1)  498  744(1)  326  535(1)  238  406(1)  184  378(1)  174  3.12 
-1.0 m  1054(1)  1007  952(1)  503  679(1)  327  489(1)  238      398(1)  204  2.80 
-1.5 m  959(1)  959(1)  761(1)  515  519(1)  335          413(1)  279  2.28 
(1) Limited by the hydraulic capacity rather than tipping load

Table 8
301.6C Lifting Capacities with a Long Stick and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              626(1)  626      668(1)  509  9.22 
6.6 ft              656(1)  619  681(1)  451  685(1)  423  10.24 
4.9 ft              762(1)  601  718(1)  445  707(1)  376  10.83 
3.3 ft      1913(1)  1223  1179(1)  804  917(1)  577  789(1)  434  731(1)  350  11.15 
1.6 ft      1428(1)  1124  1483(1)  756  1069(1)  551  864(1)  418  760(1)  343  11.15 
0  870(1)  870(1)  1695(1)  1097  1640(1)  727  1166(1)  533  910(1)  410  795(1)  352  10.86 
-1.6 ft  1556(1)  1556(1)  2160(1)  1097  1640(1)  718  1179(1)  524  895(1)  405  833(1)  383  10.24 
-3.3 ft  2323(1)  2220  2098(1)  1108  1496(1)  720  1078(1)  524      877(1)  449  9.19 
-4.9 ft  2114(1)  2114(1)  1677(1)  1135  1144(1)  738          910(1)  615  7.48 
(1) Limited by the hydraulic capacity rather than tipping load

301.8C

Table 9
301.8C Lifting Capacities with a Standard Stick, Undercarriage Retracted, and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (m) 
2.5 m              328(1)  259      331(1)  247  2.57 
2.0 m              336(1)  256      303  197  2.90 
1.5 m          445(1)  353  380(1)  249  283  183  267  172  3.11 
1.0 m          521  330  369  238  278  178  249  159  3.21 
0.5 m          500  312  358  228  272  173  245  155  3.21 
0       758(1)  458  489  302  351  221  268  170  254  160  3.12 
-0.5 m  829(1)  783  460  487  301  348  219      280  177  2.91 
-1.0 m  1080(1)  921  792  468  491  304  352  222      341  216  2.55 
-1.5 m      594(1)  483              419(1)  331  1.94 
(1) Limited by hydraulic capacity rather than tipping load

Table 10
301.8C Lifting Capacities with a Standard Stick, Undercarriage Retracted, and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              723(1)  571      729(1)  544  8.43 
6.6 ft              740(1)  564      668  434  9.51 
4.9 ft          981(1)  778  837(1)  548  623  403  588  379  10.20 
3.3 ft          1148  727  813  524  612  392  548  350  10.53 
1.6 ft          1102  687  789  502  599  381  540  341  10.53 
0      1671(1)  1009  1078  665  773  487  590  374  559  352  10.23 
-1.6 ft  1827(1)  1726  1014  1073  663  767  482      617  390  9.55 
-3.3 ft  2380(1)  2030  1746  1031  1082  670  776  489      751  476  8.37 
-4.9 ft      1309(1)  1064              923(1)  729  6.36 
(1) Limited by hydraulic capacity rather than tipping load

Table 11
301.8C Lifting Capacities with a Standard Stick, Undercarriage Retracted, and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m   2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              328(1)  285      331(1)  272  2.57 
2.0 m              336(1)  282      338(1)  218  2.90 
1.5 m          445(1)  389  380(1)  274  349(1)  203  347(1)  191  3.11 
1.0 m          591(1)  366  444(1)  263  375(1)  198  357(1)  177  3.21 
0.5 m          707(1)  347  502(1)  253  401(1)  193  371(1)  173  3.21 
0      758(1)  514  747(1)  337  532(1)  246  410(1)  189  387(1)  179  3.12 
-0.5 m  829(1)  1012(1)  517  719(1)  335  520(1)  244      405(1)  197  2.91 
-1.0 m  1080(1)  1055  900(1)  524  624(1)  339  440(1)  247      421(1)  240  2.55 
-1.5 m      594(1)  540              419(1)  368  1.94 
(1) Limited by hydraulic capacity rather than tipping load

Table 12
301.8C Lifting Capacities with a Standard Stick, Undercarriage Retracted, and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              723(1)  628      729(1)  599  8.43 
6.6 ft              740(1)  621      745(1)  480  9.51 
4.9 ft          981(1)  857  837(1)  604  769(1)  447  765(1)  421  10.20 
3.3 ft          1302(1)  806  978(1)  579  826(1)  436  787(1)  390  10.53 
1.6 ft          1558(1)  765  1106(1)  557  884(1)  425  817(1)  381  10.53 
0      1671(1)  1133  1646(1)  742  1172(1)  542  903(1)  416  853(1)  394  10.23 
-1.6 ft  1827(1)  2231(1)  1139  1585(1)  738  1146(1)  537      892(1)  434  9.55 
-3.3 ft  2380(1)  2325  1984(1)  1155  1375(1)  747  970(1)  544      928(1)  529  8.37 
-4.9 ft      1309(1)  1190              923(1)  811  6.36 
(1) Limited by hydraulic capacity rather than tipping load

Table 13
301.8C Lifting Capacities with a Standard Stick, Undercarriage Extended, and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              328(1)      331(1)  2.57 
2.0 m              336(1)      303  311  2.90 
1.5 m          445(1)  380(1)  283  291  267  274  3.11 
1.0 m          521  533  369  379  278  286  249  257  3.21 
0.5 m          500  512  358  368  272  280  245  253  3.21 
0      758(1)  489  501  351  360  268  276  254  262  3.12 
-0.5 m  829(1)  783  799  487  499  348  358      280  288  2.91 
-1.0 m  1080(1)  792  808  491  504  352  362      341  351  2.55 
-1.5 m      594(1)              419(1)  1.94 
(1) Limited by hydraulic capacity rather than tipping load

Table 14
301.8C Lifting Capacities with a Standard Stick, Undercarriage Extended, and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  S ()  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              723(1)      729(1)  8.43 
6.6 ft              740(1)      668  685  9.51 
4.9 ft          981(1)  837(1)  623  641  588  604  10.20 
3.3 ft          1148  1175  813  835  612  630  548  566  10.53 
1.6 ft          1102  1128  789  811  599  617  540  557  10.53 
0      1671(1)  1078  1104  773  793  590  608  559  577  10.23 
-1.6 ft  1827(1)  1726  1761  1073  1100  767  789      617  634  9.55 
-3.3 ft  2380(1)  1746  1781  1082  1111  776  798      751  773  8.37 
-4.9 ft      1309(1)              923(1)  6.36 
(1) Limited by hydraulic capacity rather than tipping load

Table 15
301.8C Lifting Capacities with a Standard Stick, Undercarriage Extended, and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              328(1)      331(1)  2.57 
2.0 m              336(1)      338(1)  335  2.90 
1.5 m          445(1)  380(1)  349(1)  314  347(1)  296  3.11 
1.0 m          591(1)  578  444(1)  409  375(1)  308  357(1)  277  3.21 
0.5 m          707(1)  556  502(1)  398  401(1)  303  371(1)  273  3.21 
0      758(1)  747(1)  545  532(1)  390  410(1)  299  387(1)  283  3.12 
-0.5 m  829(1)  1012(1)  880  719(1)  543  520(1)  388      405(1)  312  2.91 
-1.0 m  1080(1)  900(1)  889  624(1)  548  440(1)  392      421(1)  380  2.55 
-1.5 m      594(1)              419(1)  1.94 
(1) Limited by hydraulic capacity rather than tipping load

Table 16
301.8C Lifting Capacities with a Standard Stick, Undercarriage Extended, and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              723(1)      729(1)  8.43 
6.6 ft              740(1)      745(1)  738  9.51 
4.9 ft          981(1)  837(1)  769(1)  692  765(1)  652  10.20 
3.3 ft          1302(1)  1274  978(1)  901  826(1)  679  787(1)  610  10.53 
1.6 ft          1558(1)  1225  1106(1)  877  884(1)  668  817(1)  601  10.53 
0      1671(1)  1646(1)  1201  1172(1)  859  903(1)  659  853(1)  623  10.23 
-1.6 ft  1827(1)  2231(1)  1940  1585(1)  1197  1146(1)  855      892(1)  687  9.55 
-3.3 ft  2380(1)  1984(1)  1959  1375(1)  1208  970(1)  864      928(1)  837  8.37 
-4.9 ft      1309(1)              923(1)  6.36 
(1) Limited by hydraulic capacity rather than tipping load

Table 17
301.8C Lifting Capacities with a Long Stick, Undercarriage Retracted, and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              281(1)  265      299(1)  216  2.81 
2.0 m              294(1)  262  291  191  273  178  3.12 
1.5 m              342(1)  254  288  188  245  158  3.30 
1.0 m      847  514  530(1)  340  375  243  282  182  230  147  3.40 
0.5 m      645(1)  470  507  318  362  232  275  176  226  143  3.40 
0  391(1)  767(1)  458  492  305  353  223  270  171  233  147  3.31 
-0.5 m  703(1)  780  458  487  301  349  219  268  169  253  160  3.12 
-1.0 m  917(1)  907  786  463  489  302  350  220      297  188  2.80 
-1.5 m  830(1)  755(1)  475  498  310          408(1)  258  2.28 
(1) Limited by hydraulic capacity rather than tipping load

Table 18
301.8C Lifting Capacities with a Long Stick, Undercarriage Retracted, and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              619(1)  584      659(1)  476  9.22 
6.6 ft              648(1)  577  641  421  601  392  10.24 
4.9 ft              753(1)  559  634  414  540  348  10.83 
3.3 ft      1867  1133  1168(1)  749  826  535  621  401  507  324  11.15 
1.6 ft      1421(1)  1036  1117  701  798  511  606  388  498  315  11.15 
0  862(1)  1690(1)  1009  1084  672  778  491  595  376  513  324  10.86 
-1.6 ft  1549(1)  1719  1009  1073  663  769  482  590  372  557  352  10.24 
-3.3 ft  2021(1)  1999  1732  1020  1078  665  771  485      654  414  9.19 
-4.9 ft  1829(1)  1664(1)  1047  1097  683          899(1)  568  7.48 
(1) Limited by hydraulic capacity rather than tipping load

Table 19
301.8C Lifting Capacities with a Long Stick, Undercarriage Retracted, and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              281(1)      299(1)  237  2.81 
2.0 m              294(1)  288  305(1)  211  307(1)  197  3.12 
1.5 m              342(1)  280  322(1)  207  317(1)  175  3.30 
1.0 m      863(1)  572  530(1)  375  412(1)  269  354(1)  202  328(1)  163  3.40 
0.5 m      645(1)  526  668(1)  353  480(1)  257  388(1)  195  341(1)  160  3.40 
0  391(1)  767(1)  514  739(1)  340  524(1)  248  409(1)  190  357(1)  164  3.31 
-0.5 m  703(1)  849(1)  514  739(1)  335  530(1)  244  402(1)  188  374(1)  178  3.12 
-1.0 m  917(1)  823(1)  519  673(1)  337  484(1)  245      393(1)  209  2.80 
-1.5 m  830(1)  755(1)  532  514(1)  345          408(1)  287  2.28 
(1) Limited by hydraulic capacity rather than tipping load

Table 20
301.8C Lifting Capacities with a Long Stick, Undercarriage Retracted, and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              619(1)      659(1)  522  9.22 
6.6 ft              648(1)  634  672(1)  465  676(1)  434  10.24 
4.9 ft              753(1)  617  709(1)  456  698(1)  385  10.83 
3.3 ft      1902(1)  1261  1168(1)  826  908(1)  593  780(1)  445  723(1)  359  11.15 
1.6 ft      1421(1)  1159  1472(1)  778  1058(1)  566  855(1)  429  751(1)  352  11.15 
0  862(1)  1690(1)  1133  1629(1)  749  1155(1)  546  901(1)  418  787(1)  361  10.86 
-1.6 ft  1549(1)  1871(1)  1133  1629(1)  738  1168(1)  537  886(1)  414  824(1)  392  10.24 
-3.3 ft  2021(1)  1814(1)  1144  1483(1)  742  1067(1)  540      866(1)  460  9.19 
-4.9 ft  1829(1)  1664(1)  1172  1133(1)  760          899(1)  632  7.48 
(1) Limited by hydraulic capacity rather than tipping load

Table 21
301.8C Lifting Capacities with a Long Stick, Undercarriage Extended, and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0m 1.5m  2.0m  2.5m  3.0m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              281(1)      299(1)  2.81 
2.0 m              294(1)  291  299  273  281  3.12 
1.5 m              342(1)  288  296  245  252  3.30 
1.0 m      847  863  530(1)  375  384  282  290  230  237  3.40 
0.5 m      645(1)  507  519  362  372  275  283  226  233  3.40 
0  391(1)  767(1)  492  504  353  363  270  278  233  240  3.31 
-0.5 m  703(1)  780  796  487  499  349  358  268  276  253  261  3.12 
-1.0 m  917(1)  786  802  489  501  350  359      297  306  2.80 
-1.5 m  830(1)  755(1)  498  510          408(1)  2.28 
(1) Limited by hydraulic capacity rather than tipping load

Table 22
301.8C Lifting Capacities with a Long Stick, Undercarriage Extended, and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              619(1)      659(1)  9.22 
6.6 ft              648(1)  641  659  601  619  10.24 
4. 9 ft              753(1)  634  652  540  555  10.83 
3.3 ft      1867  1902  1168(1)  826  846  621  639  507  522  11.15 
1.6 ft      1421(1)  1117  1144  798  820  606  623  498  513  11.15 
0  862(1)  1690(1)  1084  1111  778  800  595  612  513  529  10.86 
-1.6 ft  1549(1)  1719  1754  1073  1100  769  789  590  608  557  575  10.24 
-3.3 ft  2021(1)  1732  1768  1078  1104  771  791      654  674  9.19 
-4.9 ft  1829(1)  1664(1)  1097  1124          899(1)  7.48 
(1) Limited by hydraulic capacity rather than tipping load

Table 23
301.8C Lifting Capacities with a Long Stick, Undercarriage Extended, and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0m 1.5m  2.0m  2.5m  3.0m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
2.5 m              281(1)      299(1)  2.81 
2.0 m              294(1)  305(1)  307(1)  302  3.12 
1.5 m              342(1)  322(1)  318  317(1)  271  3.30 
1.0 m      863(1)  530(1)  412(1)  354(1)  312  328(1)  256  3.40 
0.5 m      645(1)  668(1)  564  480(1)  402  388(1)  305  341(1)  252  3.40 
0  391(1)  767(1)  739(1)  549  524(1)  393  409(1)  300  357(1)  259  3.31 
-0.5 m  703(1)  849(1)  739(1)  543  530(1)  388  402(1)  298  374(1)  282  3.12 
-1.0 m  917(1)  823(1)  673  545  484(1)  389      393(1)  331  2.80 
-1.5 m  830(1)  755(1)  514(1)          408(1)  2.28 
(1) Limited by hydraulic capacity rather than tipping load

Table 24
301.8C Lifting Capacities with a Long Stick, Undercarriage Extended, and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
8.2 ft              619(1)      659(1)  9.22 
6.6 ft              648(1)  672(1)  676(1)  665  10.24 
4. 9ft              753(1)  709(1)  701  698(1)  597  10.83 
3.3 ft      1902(1)  1168(1)  908(1)  780(1)  687  723(1)  564  11.15 
1.6 ft      1421(1)  1472(1)  1243  1058(1)  886  855(1)  672  751(1)  555  11.15 
0  862(1)  1690(1)  1629(1)  1210  1155(1)  866  901(1)  661  787(1)  571  10.86 
-1.6 ft  1549(1)  1871(1)  1629(1)  1197  1168(1)  855  886(1)  656  824(1)  621  10.24 
-3.3 ft  2021(1)  1814(1)  1483(1)  1201  1067(1)  857      866(1)  729  9.19 
-4.9 ft  1829(1)  1664(1)  1133(1)          899(1)  7.48 
(1) Limited by hydraulic capacity rather than tipping load

302.5C

Table 25
302.5C Lifting Capacities with a Standard Stick and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  3.5 m  4.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
3.5 m                              629(1)  569  2.86 
3.0 m                  613(1)  525          540  442  3.31 
2.5 m                  636(1)  519  489  400      458  375  3.63 
2.0 m              802(1)  677  622  507  482  394      410  335  3.85 
1.5 m          1160  901  807  646  604  490  472  385      383  312  3.98 
1.0 m          1092  840  773  615  585  472  461  375  373  303  370  300  4.02 
0.5 m          1051(1)  816  749  593  570  457  452  365      369  299  4.00 
0      698(1)  1058  810  737  581  559  448  445  359      381  308  3.89 
-0.5 m  1104(1)  1247(1)  1059  811  733  577  555  444  442  356      409  330  3.70 
-1.0 m  1522(1)  1810(1)  1337  1066  817  736  580  556  445          465  374  3.40 
-1.5 m      1428(1)  1356  1081  830  746  589              581  465  2.95 
-2.0 m          632(1)                  551(1)  2.22 
(1) Limited by the hydraulic capacity rather than tipping load

Table 26
302.5C Lifting Capacities with a Standard Stick and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  11.5 ft  13.1 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
11.5 ft                              1387(1)  1254  9.38 
9.8 ft                  1351(1)  1157          1190  974  10.86 
8.2 ft                  1402(1)  1144  1078  882      1010  827  11.91 
6.6 ft              1768(1)  1493  1371  1118  1062  829      904  739  12.63 
4.9 ft          2557  1986  1779  1424  1332  1080  1041  849      844  688  13.06 
3.3 ft          2407  1851  1704  1356  1290  1041  1016  827  822  668  816  661  13.18 
1.6 ft          2317(1)  1799  1651  1307  1257  1008  996  805      814  659  13.12 
0      1538(1)  2332  1786  1625  1281  1232  988  981  791      840  679  12.76 
-1.6 ft  2433(1)  2749(1)  2335  1788  1615  1272  1224  979  974  785      902  728  12.14 
-3.3 ft  3355(1)  3990(1)  2948  2350  1801  1623  1279  1225  981          1025  825  11.15 
-4.9 ft      3148(1)  2989  2383  1830  1645  1299              1280  1025  9.68 
-6.6 ft          1393(1)                  1215(1)  7.28 
(1) Limited by the hydraulic capacity rather than tipping load

Table 27
302.5C Lifting Capacities with a Standard Stick and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  3.5 m  4.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
3.5 m                              629(1)  2.86 
3.0 m                  613(1)          617(1)  3.31 
2.5 m                  636(1)  613(1)      612(1)  3.63 
2.0 m              802(1)  699(1)  638(1)      612(1)  560  3.85 
1.5 m          1379(1)  970(1)  785(1)  680(1)  646      618(1)  526  3.98 
1.0 m          1136(1)  1127(1)  1075  869(1)  805  724(1)  634  631(1)  515  627(1)  510  4.02 
0.5 m          1051(1)  1217(1)  1049  928(1)  789  756(1)  624      637(1)  511  4.00 
0      698(1)  1402(1)  1231(1)  1036  946(1)  778  762(1)  617      649(1)  528  3.89 
-0.5 m  1104(1)  1247(1)  1560(1)  1524  1177(1)  1031  916(1)  773  727(1)  614      659(1)  568  3.70 
-1.0 m  1522(1)  1810(1)  1373(1)  1058(1)  1034  825(1)  775          664(1)  645  3.40 
-1.5 m      1428(1)  1093(1)  849(1)              649(1)  2.95 
-2.0 m          632(1)                  551(1)  2.22 
(1) Limited by the hydraulic capacity rather than tipping load

Table 28
302.5C Lifting Capacities with a Standard Stick and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  11.5 ft  13.1 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
11.5 ft                              1387(1)  9.86 
9.8 ft                  1351(1)          1360(1)  10.86 
8.2 ft                  1402(1)  1351(1)      1349(1)  11.91 
6.6 ft              1768(1)  1541(1)  1407(1)      1349(1)  1235  12.63 
4.9 ft          3040(1)  2138(1)  1731(1)  1499(1)  1424      1362(1)  1160  13.06 
3.3 ft          2504(1)  2485(1)  2370  1916(1)  1775  1596(1)  1398  1391(1)  1135  1382(1)  1124  13.18 
1.6 ft          2317(1)  2683(1)  2313  2046(1)  1739  1667(1)  1376      1404(1)  1127  13.12 
0      1538(1)  3091(1)  2714(1)  2284  2086(1)  1715  1680(1)  1360      1430(1)  1164  12.76 
-1.6 ft  2433(1)  2749(1)  3439(1)  3360  2595(1)  2273  2019(1)  1704  1603(1)  1354      1453(1)  1252  12.14 
-3.3 ft  3355(1)  3990(1)  3027(1)  2332(1)  2280  1819(1)  1709          1464(1)  1422  11.15 
-4.9 ft      3148(1)  2410(1)  1872(1)              1430(1)  9.68 
-6.6 ft          1393(1)                  1215(1)  7.28 
(1) Limited by the hydraulic capacity rather than tipping load

Table 29
302.5C Lifting Capacities with a Long Stick and the Blade Up
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  3.5 m  4.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
3.5 m                  530(1)          545(1)  460  3.26 
3.0 m                      495  405      459  376  3.65 
2.5 m                  548(1)  524  492  403      398  325  3.94 
2.0 m                  616(1)  511  484  396  384  313  361  294  4.14 
1.5 m          1133(1)  931  819  656  608  493  473  385  378  307  339  275  4.26 
1.0 m          1119  863  782  622  587  473  460  373  371  300  329  266  4.30 
0.5 m          1071  820  752  594  568  456  448  362  364  294  327  264  4.27 
0  566(1)  713(1)  1051  803  733  577  555  443  439  353  358  288  335  270  4.17 
-0.5 m  874(1)  1076(1)  1045  798  724  568  547  436  434  348      356  286  4.00 
-1.0 m  1211(1)  1490(1)  1307  1048  800  723  567  545  434  433  347      395  318  3.73 
-1.5 m  1601(1)  1816(1)  1324  1058  809  728  572  549  438          470  377  3.34 
-2.0 m      (1)1257  933(1)  827  702(1)  586              586(1)  508  2.76 
(1) Limited by the hydraulic capacity rather than tipping load

Table 30
302.5C Lifting Capacities with a Long Stick and the Blade Up
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
1.0m 1.5m  2.0m  2.5m  3.0m  3.5m  4.0m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
11.5 ft                  1168(1)          1202(1)  1014  10.70 
9.8 ft                      1091  893      1012  829  11.98 
8.2 ft                  1028(1)  1155  1087  888      877  717  12.93 
6.6 ft                  1358(1)  1127  1067  873  847  690  796  648  13.58 
4.9 ft          2498(1)  2053  1806  1446  1340  1087  1043  849  833  677  747  606  13.98 
3.3 ft          2467  1903  1724  1371  1294  1043  1014  822  818  661  725  586  14.11 
1.6 ft          2361  1808  1658  1310  1252  1005  988  798  802  648  721  582  14.01 
0  1248(1)  1572(1)  2317  1770  1616  1272  1224  977  968  778  789  635  739  595  13.68 
-1.6 ft  1927(1)  2372(1)  2304  1759  1596  1252  1206  961  957  767      785  631  13.12 
-3.3 ft  2670(1)  3285(1)  2881  2310  1764  1594  1250  1202  957  955  765      871  701  12.24 
-4.9 ft  3530(1)  4004(1)  2919  2332  1784  1605  1261  1210  966          1036  831  10.96 
-6.6 ft      2771(1)  2057(1)  1823  1548(1)  1292              1292(1)  1120  9.05 
(1) Limited by the hydraulic capacity rather than tipping load

Table 31
302.5C Lifting Capacities with a Long Stick and the Blade Down
All lifting capacities are in kilograms. 
Lifting point in front of swing center. 
(H)  (R) 
1.0 m 1.5 m  2.0 m  2.5 m  3.0 m  3.5 m  4.0 m  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  m 
3.5 m                  530(1)          545(1)  3.26 
3.0 m                      535(1)      542(1)  3.65 
2.5 m                  548(1)  540(1)      541(1)  3.94 
2.0 m                  616(1)  574(1)  548(1)  527  544(1)  497  4.14 
1.5 m          1133(1)  850(1)  709(1)  625(1)  571(1)  520  551(1)  470  4.26 
1.0 m          1508(1)  1030(1)  807(1)  680(1)  633  599(1)  513  561(1)  457  4.30 
0.5 m          1346(1)  1161(1)  1052  886(1)  788  726(1)  621  620(1)  505  572(1)  456  4.27 
0  566(1)  713(1)  1413(1)  1219(1)  1032  930(1)  774  751(1)  611  625(1)  500  585(1)  469  4.17 
-0.5 m  874(1)  1076(1)  1658(1)  1510  1206(1)  1022  928(1)  765  743(1)  606      597(1)  498  4.00 
-1.0 m  1211(1)  1490(1)  1512(1)  1127(1)  1021  875(1)  763  688(1)  605      607(1)  552  3.73 
-1.5 m  1601(1)  1816(1)  1284(1)  974(1)  749(1)          610(1)  3.34 
-2.0 m      1257(1)  933(1)  702(1)                586(1)  2.76 
(1) Limited by the hydraulic capacity rather than tipping load

Table 32
302.5C Lifting Capacities with a Long Stick and the Blade Down
All lifting capacities are in pounds. 
Lifting point in front of swing center. 
(H)  (R) 
3.3 ft 4.9 ft  6.6 ft  8.2 ft  9.8 ft  11.5 ft  13.1 ft  Maximum Reach 
(F) (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  (F)  (S)  ft 
11.5 ft                  1168(1)          1202(1)  10.70 
9.8 ft                      1179(1)      1195(1)  11.98 
8.2 ft                  1208(1)  1191(1)      1193(1)  12.93 
6.6 ft                  1358(1)  1265(1)  1208(1)  1162  1199  1096  13.58 
4.9 ft          2498(1)  1874(1)  1563(1)  1378(1)  1259(1)  1146  1215(1)  1036  13.98 
3.3 ft          3325(1)  2271(1)  1779(1)  1499(1)  1396  1321(1)  1131  1237(1)  1008  14.11 
1.6 ft          2967(1)  2560(1)  2319  1953(1)  1737  1601(1)  1369  1367(1)  1113  1261(1)  1005  14.01 
0  1248(1)  1572(1)  3115(1)  2687(1)  2275  2050(1)  1706  1656(1)  1347  1378(1)  1102  1290(1)  1034  13.68 
-1.6 ft  1927(1)  2372(1)  3655(1)  3329  2659(1)  2253  2046(1)  1687  1638(1)  1336      1316(1)  1098  13.12 
-3.3 ft  2670(1)  3285(1)  3333(1)  2485(1)  2251  1929(1)  1682  1517(1)  1334      1338(1)  1217  12.24 
-4.9 ft  3530(1)  4004(1)  2831(1)  2147(1)  1651(1)          1345(1)  10.96 
-6.6 ft      2771(1)  2057(1)  1548(1)              1292(1)  9.05 
(1) Limited by the hydraulic capacity rather than tipping load

Caterpillar Information System:

302.5C Mini Hydraulic Excavator Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Recoil Spring - Remove and Install
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1160 - FMI 06
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1160 - FMI 05
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1160 - FMI 03
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Bucket - Remove and Install
336D MHPU Mobile Hydraulic Power Unit Hydraulic System Check Valve (Load)
302.5C Mini Hydraulic Excavator Machine Systems Selector Valve (Alternate Pattern Control) - Remove and Install
302.5C Mini Hydraulic Excavator Engine Supplement Flywheel - Remove and Install
2005/06/27 An Improved Fuel Cap is Available {1273}
302.5C Mini Hydraulic Excavator Machine Systems Swivel - Install
GSH15 and GSH20 Orange Peel Grapples Daily Inspection
303.5C and 303C Mini Hydraulic Excavators Machine Systems Front Idler - Remove and Install
120H and 135H Motor Graders Hydraulic and Steering System Relief Valve (Scarifier)
325C Excavator Engine Supplement Aftercooler - Remove and Install
325C Excavator Engine Supplement Hydraulic Oil Cooler - Remove and Install
C15 and C18 Tier 4 Final Engines Vibration Damper - Check
303.5C and 303C Mini Hydraulic Excavators Machine Systems Recoil Spring - Remove and Install
C7.1 Engines for Caterpillar Built Machines Camshaft
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Blade - Remove and Install
324D Excavator Hydraulic System Main Control Valve
C15 and C18 Petroleum Generator Sets Engine Performance - Test - Standby Generator Sets
325C Excavator Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
325C Excavator Engine Supplement Electric Starting Motor - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.