Rotary Manifold - Assemble
Assembly Procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Lubricate all seals and all rings with clean hydraulic oil.
- Lubricate seals (7) with clean hydraulic oil. Install the seals to housing (5) .
Show/hide table
 | |
| Illustration 1 | g00684797 |
- Lubricate seal (6) with clean hydraulic oil. Install the seal to manifold (3) with the sealing lip at the top. Ensure that the seal is properly seated against the mounting plate at the bottom of the manifold. Refer to Illustration 3 for the proper orientation of the seal.
Show/hide table
 | |
| Illustration 2 | g00684795 |
Show/hide table
 | |
| Illustration 3 | g00685120 |
- Place housing (5) onto the manifold. Use a soft mallet or a hydraulic press in order to seat the housing on the manifold. Use care to ensure that the seals are not damaged during assembly.
- Lubricate seal (4) with clean hydraulic oil. Install the seal to cover (2) with the sealing lip away from the cover.
Show/hide table
 | |
| Illustration 4 | g00684793 |
- Place cover (2) into position on rotary manifold (3). Install two bolts (1) and the washers that secure the cover to the manifold. Tighten the bolts to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
Show/hide table
 | |
| Illustration 5 | g00684791 |
End By: Install the rotary manifold. Refer to Disassembly and Assembly, "Rotary Manifold - Install" for further information.
Caterpillar Information System:
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Starting Aid Switch Circuit - Test
3612 and 3616 Engines Internal Lubrication
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Front) - Time
988G Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Flash Program
3126B Engines Engine Speed - Check
3612 and 3616 Engines Engine Oil Filters
3612 and 3616 Engines Engine Oil Coolers and Temperature Regulators
3612 and 3616 Engines Centrifugal Oil Filters
723PLUS Digital Speed Control Initial Adjustments
3176C and 3196 Industrial Engines Alternator and Regulator
2000/06/01 New Pump Group With Improved Internal Sealing Used In Hydrax System {1289}
3126E Truck Engine Pistons and Connecting Rods - Remove
3500B High Displacement Locomotive Engines Air Inlet and Exhaust Lines
3612 and 3616 Engines Piston Cooling Jets
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Test
Uninterruptible Power Supply (UPS) 250 System Description
3612 and 3616 Engines Lubrication System Operation
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 2) Circuit - Test
2000/03/20 New 12 Volt AM/FM Radios Are Available {7338}
320B, 320B L, 320B LN, 322B L and 322B LN Excavators Supplement Bucket Linkage - Lubricate
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines PTO Engine RPM Set Speed (Input A and Input B) Circuit - Test
3612 and 3616 Engines Engine Oil Pump
3126B and 3126E On-highway Engines 0224-11 Theft Deterrent Active (00)
3126B and 3126E On-highway Engines 0224-14 Theft Deterrent Active with Engine Cranking (00)