Swing Brake Pressure - Test
This procedure is utilized to test the ability of the swing brake to maintain pressure and the ability of the swing brake to release pressure.
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Part Description     | Qty     |
8T-0855     | Pressure Gauge (0 to 4,000 kPa (0 to 580 psi))     | 2     |
6V-3989     | Fitting (TEST)     | 2     |
6V-4143     | Quick Connect Coupler     | 4     |
6V-3014     | Hose As     | 2     |
- Connect 4000 kPa (580 psi) pressure gauges to pressure taps (1) and (2) .
Show/hide table
Illustration 1 | g01205736 |
The remote pressure taps are located behind the left rear access door. (1) Pressure tap (Pilot pressure) |
Show/hide table
Illustration 2 | g01207575 |
Pilot Manifold (2) Pressure tap (Swing brake pressure) |
- Start the engine.
- Adjust the engine speed to position 6 by turning the engine speed dial.
- Lower the left console.
- Apply the swing lock pin.
Note: The implement lockout must not be activated.
- Swing left or right in order to release the swing brake.
- Check the pressure at pressure tap (2). The pressure should be equal to the pilot pressure.
- If the pressure at pressure tap (2) is not equal to the pilot pressure, check the pilot pressure on pressure tap (1) first.
- Release the swing joystick in order to activate the swing brake.
Note: The swing brake remains released for 3.5 seconds after the swing operation stops.
- Check the pressure at pressure tap (2). The pressure should decrease to 0 kPa (0 psi) at pressure tap (2) .
Caterpillar Information System:
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Pump Control (High Pressure Cutoff) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Pump Control (Mechanical Zero) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Pump Control (Throttle Spool Piston) - Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Main Pump (Destroke Pressure) - Test and Adjust
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fan Drive Motor
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Margin Pressure - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Control Valve (Stick Lowering) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Pressure Switch (Overload Warning) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Control Valve (Boom Lowering) - Test and Adjust
374F Excavator Swing Drive Oil - Change
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Line) - Test and Adjust - Implement
345C Excavator Machine System Specifications Front Lines
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Solenoid Valve (Swing Pump Proportional Relief) - Test and Adjust
345C Excavator Leaving the Machine
365C and 385C Excavators and 365C MHPU and 385C MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0096 - FMI 04
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
365C Excavator Equipment Lowering with Engine Stopped
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Swing Charge Pressure) - Test and Adjust
HM312 and HM315 Mulching Heads Piston Motor - Disassemble
HM312 and HM315 Mulching Heads Piston Motor - Assemble
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Swing Pump) - Test and Adjust - Line Relief Valves