Lifting Capacities - M315C Excavator with a Offset Boom (Wide Axle and Wide Dozer)
Note: These lifting capacity tables are for typical options.
Note: For more information on your specific configuration, see your dealer.
Note: The lifting capacities in the following tables represent the maximum lifting capacities. Each machine is configured differently. The following options require additional tables for lifting capacities:
- Heavy lift
- Additional counterweights
- Optional buckets
- Optional sticks
- Quick coupler
The following conditions affect the lifting capacities:
(A) - The rear dozer is up.
(B) - The rear dozer is down. The lifting capacity is over the rear.
(C) - The rear stabilizers are down. The lifting capacity is over the rear.
(D) - The front and rear stabilizers are down.
(E) - The rear dozer and front stabilizers are down.
(F) - Front Load
(S) - Side Load
Show/hide table
| M315C Excavator with a Offset Boom, 2.1 m (6.9 ft) stick and a quick coupler Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.9 (1) | 4.4 | 3.8 (1) | 2.6 | |||||||
| B | 4.9 (1) | 4.3 (1) | 3.0 | |||||||||
| C | 3.5 | |||||||||||
| D | 4.3 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 6.3 (1) | 5.4 (1) | 4.2 | 3.9 | 2.7 | ||||||
| B | 4.8 | 4.4 (1) | 3.1 | |||||||||
| C | 5.4 (1) | 3.5 | ||||||||||
| D | 4.4 (1) | |||||||||||
| E | 4.3 | |||||||||||
| 3.0 m | A | 6.8 (1) | 5.8 | 4.1 (1) | 3.8 | 2.7 | 2.5 | 1.6 | 2.1 (1) | 1.4 | 8.12 | |
| B | 6.3 (1) | 4.7 | 4.7 (1) | 3.1 | 3.9 (1) | 1.9 | 1.7 | |||||
| C | 5.3 | 3.5 | 3.6 | 2.2 | 2.0 | |||||||
| D | 6.3 (1) | 4.7 | 3.9 (1) | 3.3 | 2.1 (1) | |||||||
| E | 4.2 (1) | 2.8 | ||||||||||
| 1.5 m | A | 9.1 (1) | 7.2 | 5.7 | 4.0 | 3.8 | 2.6 | 2.4 | 1.5 | 2.1 | 1.3 | 8.22 |
| B | 8.4 | 6.9 (1) | 4.6 | 5.0 (1) | 3.0 | 3.9 (1) | 1.8 | 2.2 (1) | 1.6 | |||
| C | 9.1 (1) | 5.2 | 3.4 | 3.6 | 2.2 | 1.9 | ||||||
| D | 6.9 (1) | 4.7 | 3.9 (1) | 3.2 | 2.2 (1) | |||||||
| E | 6.3 | 4.2 (1) | 2.8 | |||||||||
| 0.0 m | A | 10.6 (1) | 7.1 | 5.8 | 3.9 | 3.6 | 2.4 | 2.3 | 1.5 | 2.2 | 1.3 | 8.01 |
| B | 8.5 | 7.0 (1) | 4.5 | 5.0 (1) | 2.8 | 3.5 (1) | 1.8 | 2.3 (1) | 1.6 | |||
| C | 9.8 | 5.3 | 3.3 | 2.1 | 1.9 | |||||||
| D | 10.6 (1) | 7.0 (1) | 4.7 | 3.1 | 2.3 (1) | |||||||
| E | 6.4 | 4.1 | 2.7 | |||||||||
| -1.5 m | A | 11.2 | 6.8 | 5.7 | 3.7 | 3.4 | 2.2 | 2.4 | 1.5 | 7.45 | ||
| B | 11.5 (1) | 8.2 | 7.1 (1) | 4.3 | 5.0 (1) | 2.6 | 2.6 (1) | 1.8 | ||||
| C | 9.9 | 5.1 | 3.1 | 2.1 | ||||||||
| D | 11.5 (1) | 7.1 (1) | 4.6 | 2.6 (1) | ||||||||
| E | 6.5 | 3.9 | ||||||||||
| -3.0 m | A | 11.4 | 6.8 | 5.4 | 3.4 | |||||||
| B | 11.8 (1) | 8.3 | 6.6 (1) | 4.1 | ||||||||
| C | 9.9 | 4.8 | ||||||||||
| D | 11.8 (1) | 6.6 (1) | ||||||||||
| E | 6.2 | |||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a Offset Boom, 2.1 m (6.9 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.9 (1) | 4.6 | 4.1 | 2.8 | |||||||
| B | 4.9 (1) | 4.3 (1) | 3.2 | |||||||||
| C | 3.7 | |||||||||||
| D | 4.3 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 6.3 (1) | 5.4 (1) | 4.5 | 4.0 | 2.8 | ||||||
| B | 5.1 | 4.4 (1) | 3.3 | |||||||||
| C | 5.4 (1) | 3.7 (1) | ||||||||||
| D | 4.4 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 6.8 (1) | 6.0 | 4.3 | 4.0 | 2.8 | 2.6 | 1.7 | 2.1 (1) | 1.5 | 8.12 | |
| B | 6.3 (1) | 4.9 | 4.7 (1) | 3.3 | 3.9 (1) | 2.0 | 1.8 | |||||
| C | 5.5 | 3.7 | 3.8 | 2.4 | 2.1 | |||||||
| D | 6.3 (1) | 4.7 (1) | 3.9 (1) | 3.4 | 2.1 (1) | |||||||
| E | 4.4 (1) | 3.0 | ||||||||||
| 1.5 m | A | 9.1 (1) | 7.6 (1) | 5.9 | 4.2 | 4.0 (1) | 2.7 | 2.6 | 1.7 | 2.2 (1) | 1.4 | 8.22 |
| B | 8.7 | 6.9 (1) | 4.8 | 5.0 (1) | 3.2 | 3.9 (1) | 2.0 | 1.7 | ||||
| C | 9.1 (1) | 5.4 | 3.6 | 3.8 | 2.3 | 2.0 | ||||||
| D | 6.9 (1) | 4.8 | 3.9 (1) | 3.4 | 2.2 (1) | |||||||
| E | 6.5 | 4.4 | 2.9 | |||||||||
| 0.0 m | A | 10.6 (1) | 7.5 | 6.0 | 4.1 | 3.8 | 2.5 | 2.5 | 1.6 | 2.3 | 1.5 | 8.01 |
| B | 8.9 | 7.0 (1) | 4.8 | 5.0 (1) | 3.0 | 3.5 (1) | 1.9 | 2.3 (1) | 1.8 | |||
| C | 10.2 | 5.5 | 3.5 | 2.2 | 2.1 | |||||||
| D | 10.6 (1) | 7.0 (1) | 4.9 (1) | 3.3 | 2.3 (1) | |||||||
| E | 6.6 | 4.3 | 2.9 | |||||||||
| -1.5 m | A | 11.5 (1) | 7.5 | 6.0 | 3.9 | 3.7 | 2.4 | 2.6 | 1.6 | 7.45 | ||
| B | 8.7 | 7.1 (1) | 4.6 | 5.0 (1) | 2.8 | 2.6 (1) | 2.0 | |||||
| C | 10.4 | 5.4 | 3.3 | 2.3 | ||||||||
| D | 11.5 (1) | 7.1 (1) | 4.8 | 2.6 (1) | ||||||||
| E | 6.8 | 4.2 | ||||||||||
| -3.0 m | A | 11.8 (1) | 7.3 | 5.7 | 3.7 | |||||||
| B | 8.8 | 6.6 (1) | 4.4 | |||||||||
| C | 10.5 | 5.1 | ||||||||||
| D | 11.8 (1) | 6.6 (1) | ||||||||||
| E | 6.6 | |||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a Offset Boom, 2.4 m (7.9 ft) stick and a quick coupler Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.4 (1) | 4.4 | 3.9 | 2.7 | |||||||
| B | 4.4 (1) | 4.1 (1) | 3.1 | |||||||||
| C | 3.6 | |||||||||||
| D | 4.1 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.8 (1) | 5.2 (1) | 4.3 | 3.9 | 2.7 | 2.5 | 1.6 | ||||
| B | 4.9 | 4.3 (1) | 3.1 | 2.6 (1) | 1.9 | |||||||
| C | 5.2 (1) | 3.5 | 2.3 | |||||||||
| D | 4.3 (1) | 2.6 (1) | ||||||||||
| E | ||||||||||||
| 3.0 m | A | 7.0 (1) | 5.8 | 4.1 | 3.8 | 2.7 | 2.5 | 1.6 | 1.8 (1) | 1.3 | 8.40 | |
| B | 6.1 (1) | 4.7 | 4.6 (1) | 3.1 | 3.8 (1) | 1.9 | 1.6 | |||||
| C | 5.3 | 3.5 | 3.7 | 2.3 | 1.8 (1) | |||||||
| D | 6.1 (1) | 4.6 (1) | 3.8 (1) | 3.3 | ||||||||
| E | 4.2 | 2.9 | ||||||||||
| 1.5 m | A | 8.8 (1) | 7.2 | 5.6 | 4.0 (1) | 3.8 | 2.6 | 2.5 | 1.6 | 1.9 (1) | 1.2 | 8.49 |
| B | 8.3 (1) | 6.8 (1) | 4.6 (1) | 4.9 (1) | 3.1 | 3.8 (1) | 1.9 | 1.5 | ||||
| C | 8.8 (1) | 5.2 | 3.5 (1) | 3.6 | 2.2 | 1.8 | ||||||
| D | 6.8 (1) | 4.6 (1) | 3.8 (1) | 3.3 | 1.9 (1) | |||||||
| E | 6.3 (1) | 4.2 | 2.8 | |||||||||
| 0.0 m | A | 10.4 (1) | 7.1 | 5.7 (1) | 3.9 | 3.7 | 2.4 | 2.4 | 1.5 | 2.0 | 1.3 | 8.29 |
| B | 8.5 | 6.9 (1) | 4.6 | 5.0 (1) | 2.9 | 3.7 (1) | 1.8 | 2.0 (1) | 1.5 | |||
| C | 9.8 | 5.2 | 3.3 | 3.5 | 2.1 | 1.8 | ||||||
| D | 10.4 (1) | 6.9 (1) | 4.7 (1) | 3.7 (1) | 3.2 | 2.0 (1) | ||||||
| E | 6.3 | 4.2 | 2.7 | |||||||||
| -1.5 m | A | 11.1 (1) | 6.8 | 5.7 | 3.7 | 3.5 | 2.2 | 2.2 | 1.4 | 7.75 | ||
| B | 11.4 (1) | 8.2 | 7.1 (1) | 4.3 | 5.1 (1) | 2.6 | 2.3 (1) | 1.7 | ||||
| C | 9.9 | 5.1 | 3.1 | 2.0 | ||||||||
| D | 11.4 (1) | 7.1 (1) | 4.6 | 2.3 (1) | ||||||||
| E | 6.5 | 4.0 | ||||||||||
| -3.0 m | A | 11.3 | 6.7 | 5.4 | 3.5 | 3.3 | 2.1 | |||||
| B | 11.9 (1) | 8.2 | 7.0 (1) | 4.1 | 3.6 (1) | 2.5 | ||||||
| C | 9.8 | 4.8 | 3.0 | |||||||||
| D | 11.9 (1) | 7.0 (1) | 3.6 (1) | |||||||||
| E | 6.3 | |||||||||||
| -4.5 m | A | 7.0 (1) | 6.6 | |||||||||
| B | 7.0 (1) | |||||||||||
| C | ||||||||||||
| D | ||||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a Offset Boom, 2.4 m (7.9 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.4 (1) | 4.1 | 2.8 | ||||||||
| B | 4.1 (1) | 3.3 | ||||||||||
| C | 3.7 | |||||||||||
| D | 4.1 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.8 (1) | 5.2 (1) | 4.5 | 4.0 (1) | 2.9 | 2.6 (1) | 1.8 | ||||
| B | 5.1 | 4.3 (1) | 3.3 | 2.1 | ||||||||
| C | 5.2 (1) | 3.7 | 2.4 | |||||||||
| D | 4.3 (1) | 2.6 (1) | ||||||||||
| E | ||||||||||||
| 3.0 m | A | 7.0 (1) | 6.0 | 4.3 | 4.0 | 2.9 | 2.7 | 1.8 | 1.8 (1) | 1.4 | 8.40 | |
| B | 6.1 (1) | 4.9 | 4.6 (1) | 3.2 | 3.8 (1) | 2.1 | 1.7 | |||||
| C | 5.6 | 3.7 | 2.4 | 1.8 (1) | ||||||||
| D | 6.1 (1) | 4.6 (1) | 3.5 | |||||||||
| E | 4.4 | 3.0 | ||||||||||
| 1.5 m | A | 8.8 (1) | 7.5 | 5.9 | 4.2 | 4.0 | 2.8 | 2.6 | 1.7 | 1.9 (1) | 1.3 | 8.49 |
| B | 8.8 (1) | 6.8 (1) | 4.8 (1) | 4.9 (1) | 3.2 | 3.8 (1) | 2.0 | 1.6 | ||||
| C | 5.4 (1) | 3.7 | 3.8 | 2.4 | 1.9 | |||||||
| D | 6.8 (1) | 4.8 | 3.8 (1) | 3.4 | 1.9 (1) | |||||||
| E | 6.5 (1) | 4.3 | 3.0 | |||||||||
| 0.0 m | A | 10.4 (1) | 7.6 | 5.9 | 4.1 | 3.9 (1) | 2.6 | 2.5 | 1.6 | 2.0 (1) | 1.4 | 8.29 |
| B | 8.8 (1) | 6.9 (1) | 4.8 | 5.0 (1) | 3.0 | 3.7 (1) | 1.9 | 1.6 | ||||
| C | 10.2 (1) | 5.5 | 3.5 | 3.7 | 2.3 | 1.9 | ||||||
| D | 10.4 (1) | 6.9 (1) | 4.8 | 3.7 (1) | 3.3 | 2.0 (1) | ||||||
| E | 6.6 (1) | 4.4 | 2.9 | |||||||||
| -1.5 m | A | 11.4 | 7.2 | 6.0 | 3.9 | 3.7 | 2.4 | 2.3 (1) | 1.5 | 7.75 | ||
| B | 11.4 (1) | 8.7 | 7.1 (1) | 4.6 | 5.1 (1) | 2.8 | 1.8 | |||||
| C | 10.4 | 5.4 | 3.3 | 2.2 | ||||||||
| D | 11.4 (1) | 7.1 (1) | 4.8 | 2.3 (1) | ||||||||
| E | 6.8 | 4.2 | ||||||||||
| -3.0 m | A | 11.9 (1) | 7.2 | 5.8 | 3.7 | 3.5 | 2.3 | |||||
| B | 8.7 | 7.0 (1) | 4.4 | 3.6 (1) | 2.7 | |||||||
| C | 10.4 | 5.1 | 3.2 | |||||||||
| D | 11.9 (1) | 7.0 (1) | 3.6 (1) | |||||||||
| E | 6.6 | |||||||||||
| -4.5 m | A | 7.0 (1) | ||||||||||
| B | ||||||||||||
| C | ||||||||||||
| D | ||||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a Offset Boom, 2.6 m (8.5 ft) stick and a quick coupler Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.0 (1) | 3.9 | 2.5 | ||||||||
| B | 4.0 (1) | 2.9 | ||||||||||
| C | 3.5 | |||||||||||
| D | 4.0 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.7 (1) | 4.0 | 3.9 | 2.5 | 2.6 | 1.5 | |||||
| B | 4.5 | 4.2 (1) | 2.9 | 3.2 (1) | 1.8 | |||||||
| C | 4.7 (1) | 3.4 (1) | 2.2 | |||||||||
| D | 4.2 (1) | 3.2 (1) | ||||||||||
| E | 4.1 | 2.8 | ||||||||||
| 3.0 m | A | 7.0 (1) | 6.9 | 5.8 (1) | 3.8 | 3.8 (1) | 2.5 | 2.6 | 1.5 | 1.7 (1) | 1.1 | 8.59 |
| B | 7.0 (1) | 6.0 (1) | 4.3 | 4.5 (1) | 2.9 | 3.8 (1) | 1.8 | 1.4 | ||||
| C | 5.1 | 3.4 | 3.7 | 2.2 | 1.7 (1) | |||||||
| D | 6.0 (1) | 4.5 (1) | 3.8 (1) | 3.3 | ||||||||
| E | 4.0 | 2.8 | ||||||||||
| 1.5 m | A | 8.8 (1) | 6.7 | 5.6 | 3.7 | 3.8 | 2.5 | 2.5 | 1.5 | 1.7 (1) | 1.1 | 8.69 |
| B | 7.7 | 6.7 (1) | 4.3 | 4.9 (1) | 2.8 | 3.8 (1) | 1.7 | 1.3 | ||||
| C | 8.8 (1) | 5.0 (1) | 3.4 (1) | 3.6 | 2.2 | 1.6 | ||||||
| D | 6.7 (1) | 4.6 (1) | 3.8 (1) | 3.3 | 1.7 (1) | |||||||
| E | 6.0 | 4.0 (1) | 2.7 | |||||||||
| 0.0 m | A | 10.1 (1) | 6.5 | 5.7 (1) | 3.6 | 3.7 | 2.3 | 2.4 | 1.4 | 1.9 (1) | 1.1 | 8.49 |
| B | 7.7 (1) | 6.9 (1) | 4.2 | 5.0 (1) | 2.7 | 3.8 (1) | 1.6 | 1.3 | ||||
| C | 9.3 | 5.1 | 3.2 | 3.6 | 2.1 | 1.7 | ||||||
| D | 10.1 (1) | 6.9 (1) | 4.7 (1) | 3.8 (1) | 3.2 | 1.9 (1) | ||||||
| E | 6.0 (1) | 4.0 | 2.6 | |||||||||
| -1.5 m | A | 11.0 (1) | 6.1 | 5.7 | 3.4 | 3.5 | 2.1 | 2.3 | 1.3 | 2.1 (1) | 1.2 | 7.97 |
| B | 11.3 (1) | 7.3 | 7.0 (1) | 4.0 | 5.1 (1) | 2.4 | 3.0 (1) | 1.6 | 1.4 | |||
| C | 9.4 | 4.9 | 3.0 | 2.0 | 1.8 | |||||||
| D | 11.3 (1) | 7.0 (1) | 4.6 | 3.0 (1) | 2.1 (1) | |||||||
| E | 6.2 | 3.8 | 2.5 | |||||||||
| -3.0 m | A | 11.3 | 6.0 | 5.5 | 3.2 | 3.4 | 1.9 | |||||
| B | 11.8 (1) | 7.3 | 7.2 (1) | 3.8 | 4.1 (1) | 2.3 | ||||||
| C | 9.3 | 4.7 | 3.0 | |||||||||
| D | 11.8 (1) | 7.2 (1) | 4.1 (1) | |||||||||
| E | 6.0 | 3.7 | ||||||||||
| -4.5 m | A | 8.3 (1) | 6.0 | |||||||||
| B | 7.2 | |||||||||||
| C | 8.3 (1) | |||||||||||
| D | ||||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a Offset Boom, 2.6 m (8.5 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.0 (1) | 4.0 (1) | 2.9 | ||||||||
| B | 3.3 | |||||||||||
| C | 3.8 | |||||||||||
| D | 4.0 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.7 (1) | 4.5 | 4.0 (1) | 2.9 | 2.7 | 1.8 | |||||
| B | 4.7 (1) | 4.2 (1) | 3.3 (1) | 3.2 (1) | 2.1 | |||||||
| C | 3.7 | 2.5 | ||||||||||
| D | 4.2 (1) | 3.2 (1) | ||||||||||
| E | 3.1 | |||||||||||
| 3.0 m | A | 7.0 (1) | 6.0 (1) | 4.3 | 4.0 | 2.9 | 2.7 | 1.8 | 1.7 (1) | 1.4 | 8.59 | |
| B | 4.9 | 4.5 (1) | 3.3 | 3.8 (1) | 2.1 | 1.6 | ||||||
| C | 5.6 | 3.7 | 2.5 | 1.7 (1) | ||||||||
| D | 6.0 (1) | 4.5 (1) | 3.5 | |||||||||
| E | 4.4 | 3.1 | ||||||||||
| 1.5 m | A | 8.8 (1) | 7.5 | 5.9 | 4.2 | 3.9 | 2.8 | 2.7 | 1.7 | 1.7 (1) | 1.3 | 8.69 |
| B | 8.7 (1) | 6.7 (1) | 4.8 (1) | 4.9 (1) | 3.2 (1) | 3.8 (1) | 2.1 | 1.6 | ||||
| C | 8.8 (1) | 5.4 | 3.6 | 3.8 | 2.4 | 1.7 (1) | ||||||
| D | 6.7 (1) | 4.8 | 3.8 (1) | 3.5 | ||||||||
| E | 6.5 (1) | 4.3 | 3.0 (1) | |||||||||
| 0.0 m | A | 10.1 (1) | 7.7 | 5.9 | 4.2 | 3.9 | 2.7 | 2.6 | 1.7 | 1.9 (1) | 1.3 | 8.49 |
| B | 8.8 | 6.9 (1) | 4.8 | 5.0 (1) | 3.1 | 3.8 (1) | 2.0 | 1.6 | ||||
| C | 10.1 | 5.5 | 3.6 | 3.8 | 2.3 | 1.9 | ||||||
| D | 10.1 (1) | 6.9 (1) | 4.8 | 3.8 (1) | 3.4 | 1.9 (1) | ||||||
| E | 6.5 | 4.4 (1) | 2.9 | |||||||||
| -1.5 m | A | 11.3 (1) | 7.2 | 6.0 | 3.9 | 3.7 | 2.4 | 2.5 | 1.6 | 2.1 (1) | 1.5 | 7.97 |
| B | 8.7 | 7.0 (1) | 4.6 | 5.1 (1) | 2.9 | 3.0 (1) | 1.9 | 1.7 | ||||
| C | 10.4 (1) | 5.4 | 3.4 | 2.2 | 2.1 | |||||||
| D | 11.3 (1) | 7.0 (1) | 4.9 | 3.0 (1) | 2.1 (1) | |||||||
| E | 6.7 (1) | 4.2 | 2.8 | |||||||||
| -3.0 m | A | 11.8 (1) | 7.1 | 5.8 | 3.8 | 3.6 | 2.3 | |||||
| B | 8.6 | 7.2 (1) | 4.4 | 4.1 (1) | 2.7 | |||||||
| C | 10.4 | 5.2 | 3.2 | |||||||||
| D | 11.8 (1) | 7.2 (1) | 4.1 (1) | |||||||||
| E | 6.7 | 4.1 | ||||||||||
| -4.5 m | A | 8.3 (1) | 7.1 | |||||||||
| B | 8.3 (1) | |||||||||||
| C | ||||||||||||
| D | ||||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Caterpillar Information System:
2006/02/13 Two Adjustment Gauges Help the Technician Set the Lash for the Variable Valve Actuators {0703, 0763, 1100, 1209}
Supplemental Product Support Literature for the Field Installation of a 20 kW Right Front Corner Mounted Generator Set ( 223-4514 Hydraulic Generator Arrangement) and Operation Instructions {1404, 4450, 5050, 7000} Supplemental Product Support Literature for the Field Installation of a 20 kW Right Front Corner Mounted Generator Set ( 223-4514 Hydraulic Generator Arrangement) and Operation Instructions {1404, 4450, 5050, 7000}
2004/06/01 A New Special Instruction, REHS2259 , "Fabricated Tool for Alternate Method of Tightening Fan Drive Belts" is Available {1357, 1397}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
2004/06/14 New Harder Cylinder Pistons Are Available {5456, 5457, 5458}
2004/06/14 An Improved Bushing is Now Available for Mini Hydraulic Excavators {6508}
2004/06/21 A New Washer Prevents Oil Leakage From The Hydraulic Pump {507G, 5084}
2004/07/05 243-3133 Quick Connect Coupler (Fluid Sampling) Provides A Coupler for Portable Particle Analyzers {0707, 0717, 0731, 0732, 0738}
325D and 329D Excavators Indicators and Gauges - Test
2004/06/28 210-6990 Pressure Gauge (LCD Display, 0 to 500-PSI) Is Available for Use by Technicians {0770}
325D and 329D Excavators Operation Information
325D and 329D Excavators Engine and Machine Warm-Up
Fabricated Tool for Alternate Method of Tightening Fan Drive Belts{1357, 1397} Fabricated Tool for Alternate Method of Tightening Fan Drive Belts{1357, 1397}
2004/06/21 New Procedure Will Improve Recirculation Filter's Serviceability {7342}
324D and 326D Excavators Work Tool Control Pedal - If Equipped
385C Excavator and 385C MHPU Mobile Hydraulic Power Unit Service Hour Meter
M325C Material Handler Hydraulic System Oil Sample - Obtain
C11 and C13 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
325D and 329D Excavators Air Conditioning and Heating Control
318C and 319C Excavators Engine Oil Sample - Obtain
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
2004/06/07 An Improved Service Brake Control Valve Is Available {1435, 4265, 5051}
312C Excavator Lifting Capacities - 312C with a Reach Boom
312C Excavator Lifting Capacities - 312C L with a VA Boom and a 2.49 m Blade