Travel Motor - Test - Measurement of Case Drain Oil
Show/hide table
Required Tools | ||
---|---|---|
Part Number | Description | Qty |
FT-2542 | Track block assembly | 1 |
6V-9508 | Face Seal Plug | 1 |
6V-8397 | O-Ring Seal | 1 |
Remote drain hose with an inside diameter of |
1 | |
Container for measuring | 1 |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Stop the engine.
- Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Show/hide table
Illustration 1 g00729025 Sprocket (left track)
(1) Sprocket
(2) FT-2542 Track block assembly - Place track block assembly (2) in sprocket (1) in order to block forward left travel. Refer to Illustration 1.
Show/hide table
Illustration 2 g00728610 Travel motor
(3) 6V-9508 Face seal plug
(4) 6V-8397 O-Ring seal
(5) Case drain hose
(6) Connector
(7) Remote drain hose
(8) Container for measuring - Disconnect case drain hose (5) from connector (6). Install plug (3) and seal (4) in the open end of case drain hose (5).
- Connect one end of remote drain hose (7) to connector (6). Place the other end of remote drain hose into the container (8) in order to measure the case drain oil.
- Start the engine.
- Place the machine controls at the following settings: engine speed dial "10" and Low idle switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test" for engine rpm settings.
- Place the hydraulic activation control lever in the UNLOCKED position.
- Increase the hydraulic oil temperature to
55° ± 5°C (131° ± 9°F) . - Move the left travel lever forward fully for one minute.
- Measure the amount of case drain oil.
- Remove track block assembly (2) from sprocket (1).
- Move the left travel lever in order to reposition the travel motor.
- Place track block assembly (2) in sprocket (1) in order to block forward left travel.
- Repeat Steps 10 through 14 in order to obtain three measurements of case drain oil.
The following values specify the maximum acceptable flow of case drain oil when the main relief valve pressure is set at
- New travel motor ...
20 L/min (5.3 US gpm) - Rebuilt travel motor ...
23 L/min (6.1 US gpm) - Rebuilt travel motor ...
Caterpillar Information System:
325C Excavator 3126B Engine Supplement Muffler - Remove and Install - Engine in Chassis
314C CR Excavator Hydraulic System Main Hydraulic Pump
2002/02/11 Guideline for Reusable Parts and Salvage Operations, SEBF8474 , "Caterpillar Hydraulic Hammers" is Available {6333}
325C Excavator 3126B Engine Supplement Radiator - Remove - Engine in Chassis
C-9 Engine for the 330C Excavator and for the 330C Mobile Hydraulic Power Unit Low Power/Poor or No Response to Throttle
314C CR Excavator Machine System Specifications Main Hydraulic Pump
N3 Series Brushless Alternators General Information
314C CR Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
322C Forest Machine Machine Systems Stick Cylinder - Install
Installation of a Four-Way Pilot Valve Group (Control Pattern Change) {5059} Installation of a Four-Way Pilot Valve Group (Control Pattern Change) {5059}
314C CR Excavator Machine System Specifications Final Drives and Travel Motors
5230B Excavator Machine Systems Pump Drive - Assemble
325C Excavator 3126B Engine Supplement Radiator - Install - Engine in Chassis
312C, 315C, 318C, 319C, 320C, 322C, 325C and 330C Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
N3 Series Brushless Alternators Component Description
305 Mini Hydraulic Excavator Machine Systems Fuel Tank - Remove
304 Mini Hydraulic ExcavatorEngine Supplement and Machine Systems Travel Motor - Disassemble
5230B Excavator Machine Systems Pump Drive - Remove
314C CR Excavator Machine System Specifications Swing Motor
5230B Excavator Machine Systems Fan Motor (Radiator Cooling) - Install
C-9 Engine for the 973C Track-Type Loader CID 0091 FMI 02 Incorrect Throttle Switch inputs
312C, 315C, 318C, 319C, 320C, 322C, 325C and 330C Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
304 Mini Hydraulic ExcavatorEngine Supplement and Machine Systems Travel Motor - Assemble
C-9 Engine for the 12H Motor Grader CID 0175 FMI 03 Engine Oil Temperature open/short to +batt