Cylinder Head - Remove
Removal Procedure
Start By:
- Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Remove".
- Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
- Remove the water temperature regulator housing. Refer to Disassembly and Assembly, "Water Temperature Regulator Housing - Remove".
- Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove and Install".
- Gradually loosen 22 cylinder head bolts (1) in the reverse order that is shown above. This will help prevent possible distortion of the cylinder head during removal.
Show/hide table
Illustration 1 | g00646441 |
Show/hide table
Illustration 2 | g00550162 |
- Attach a suitable lifting device to cylinder head (2). Carefully lift cylinder head (2) off the cylinder block. The weight of the cylinder head is 36 kg (80 lb).
Show/hide table
Illustration 3 | g00646445 |
- Remove cylinder head gasket (4) from the top of the cylinder block.
Show/hide table
NOTICE |
---|
Place the cylinder head on a surface that will not scratch the face of the cylinder head. |
Show/hide table
Illustration 4 | g00646475 |
- Note the location of dowels (3) on each end of the cylinder block. Dowels (3) hold cylinder head gasket (4) in place while the cylinder head is installed. Inspect the condition of dowels (3). If the dowels are damaged, use new parts for replacement.
Caterpillar Information System:
3126B Marine Engine Exhaust Manifold - Remove and Install
3126B and 3126E On-highway Engines 0084-10 Vehicle Speed signal rate of change (36)
3126B Marine Engine Auxiliary Water Pump - Disassemble
3618 Engine Cylinder Liner - Install
Uninterruptible Power Supply (UPS) 250 Time and Date Adjustment
3126B and 3126E On-highway Engines 0084-08 Vehicle Speed signal out of range (36)
3126B and 3126E On-highway Engines 0084-02 Vehicle Speed signal invalid (36)
3126B and 3126E On-highway Engines 0084-01 Vehicle Speed loss of signal (31)
3408E and 3412E Industrial Engines Electronic Service Tools
3126B and 3126E On-highway Engines 0091-13 Throttle Position out of calibration (28)
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application 0030-13 PTO Throttle Sensor Calibration (29)
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application 0030-08 Invalid PTO Throttle Signal (29)
Uninterruptible Power Supply (UPS) 250 Oil - Change
Uninterruptible Power Supply (UPS) 250 Display Contrast Adjustment
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Electronic Display Module - If Equipped
Uninterruptible Power Supply (UPS) 250 Oil Level - Check
Uninterruptible Power Supply (UPS) 250 Sight Gauge - Clean
Caterpillar Monitoring System for Electronic Modular Control Panel CID 0828 FMI 08 Temperature Sensor (Right Exhaust) Abnormal Signal - Test
Uninterruptible Power Supply (UPS) 250 Air Filter - Replace
Caterpillar Monitoring System for Electronic Modular Control Panel CID 0460 FMI 08 Pressure Sensor (Fuel) Abnormal Signal - Test
Uninterruptible Power Supply (UPS) 250 Bearing - Replace
Uninterruptible Power Supply (UPS) 250 Flywheel - Clean
Uninterruptible Power Supply (UPS) 250 General Operation
Uninterruptible Power Supply (UPS) 250 Placing the System On-line