Engine Oil Relief Valve
Show/hide table
Illustration 1 | g00295480 |
(1) Spring
- Length under test force ... 59.8 mm (2.35 inch)
- Length under test force for engines that are equipped with a balancer unit ... 42.7 mm (1.681 inch)
- Test force ... 15.9 to 23.1 N (3.6 to 5.2 lb)
- Test force for engines that are equipped with a balancer unit ... 34 to 38 N (7.6 to 8.5 lb)
- The relief valve for the engine oil pressure should open at the following pressure: ... 340 to 395 kPa (49 to 57 psi)
- If the engine is equipped with a balancer unit, the relief valve for the engine oil pressure should open at the following pressure: ... 523 kPa (76 psi)
(2) Relief valve plunger
- Outside diameter of the relief valve plunger ... 18.16 to 18.18 mm (0.715 to 0.716 inch)
- Outside diameter of the relief valve plunger on engines that are equipped with a balancer unit ... 15.95 to 15.98 mm (0.628 to 0.629 inch)
- Clearance of the relief valve plunger in the bore of the relief valve housing ... 0.06 to 0.11 mm (0.002 to 0.004 inch)
- Clearance of the relief valve plunger in the bore of the relief valve housing on engines that are equipped with a balancer unit ... 0.02 to 0.08 mm (0.0008 to 0.0031 inch)
(3) Relief valve housing
- Diameter of the bore in the relief valve housing ... 18.24 to 18.27 mm (0.718 to 0.719 inch)
- Diameter of the bore in the relief valve housing for engines that are equipped with a balancer unit ... 16.00 to 16.03 mm (0.630 to 0.631 inch)
(4) Bolt
- Tighten the bolt to the following torque: ... 44 N·m (33 lb ft)
Caterpillar Information System:
3054B Industrial Engine Air Inlet Heater
C-9 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor
3612 and 3616 Engines Cylinder Head - Disassemble
C-9 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor
3512B Marine Auxiliary Engine After Starting Engine
C-9 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
C9 Urban Transit Bus Engine Speed/Timing Sensor
Caterpillar Monitoring System for Electronic Modular Control Panel Sensor Signal Voltage - Test
Caterpillar Monitoring System for Electronic Modular Control Panel Pulse Width Modulated (PWM) Sensor - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Multi-Torque - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Temperature Sensor Open or Short Circuit - Test
Caterpillar Monitoring System for Electronic Modular Control Panel Sensor Dynamic Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Install
3056E Industrial Engine Electric Starting Motor
C-9 Engines for Caterpillar Built Machines Cooling System
C-9 Engines for Caterpillar Built Machines Electrical System
G3606 and G3608 Engines Water Temperature Regulator and Housing - Disassemble
3054B Industrial Engine Cylinder Block
G3606 and G3608 Engines Water Temperature Regulator and Housing - Assemble
3512B Marine Auxiliary Engine Generator Oil - Change
3114, 3116, and 3126 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
G3606 and G3608 Engines Water Temperature Regulator and Housing - Install
3612 and 3616 Engines Cylinder Head - Assemble