Auger Planetary - Disassemble
Disassembly Procedure
Show/hide table
REQUIRED TOOLS     | |||
Tool     | Part Number     | Part Description     | Quantity     |
A     | 2P-2813     | Snap Ring Pliers     | 1     |
B     | 1P-0074     | Slide Hammer Puller     | 1     |
Start By:
- Remove the gear motor from the auger planetary. Refer to Service Manual, "Gear Motor - Remove".
- Remove twelve bolts (1) from the top of the auger planetary. Remove cover plate (2) from the ring gear (3) .
Show/hide table
Illustration 1 | g00683179 |
- Remove thrust washer (4) .
Show/hide table
Illustration 2 | g00683190 |
- Remove sun gear (5) .
- Remove the upper carrier and planetary gear (6) .
- Remove the lower carrier and planetary gear (7) .
Show/hide table
Illustration 3 | g00682980 |
- Remove ring gear (3) .
Show/hide table
Illustration 4 | g00683092 |
- Use tooling (A) to remove retaining ring (8) .
Show/hide table
Illustration 5 | g00683103 |
- Remove upper bearing (9) .
- Remove shaft (10) .
- Use tooling (B) to remove dust seal (11). Position tooling (B) between dust seal (11) and the bearing.
Show/hide table
Illustration 6 | g00683133 |
- Remove lower bearing (12) .
Show/hide table
Illustration 7 | g00683170 |
- Use tooling (B) to remove lower bearing cone (13) .
Show/hide table
Illustration 8 | g00683161 |
- Use tooling (B) to remove upper bearing cone (14) .
Show/hide table
Illustration 9 | g00683172 |
Caterpillar Information System:
303.5 Mini Hydraulic Excavator Pilot and Travel Speed Manifold
303.5 Mini Hydraulic Excavator Machine Systems Fuel Tank - Remove
2004/09/06 Product Support Literature for Custom Product Machines {0374}
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Install
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Remove
325C and 325C L Excavator Fuel Tank Shutoff and Drain Control
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Disassemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325D and 329D Excavators Joystick Controls Alternate Patterns
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Remove - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
315C Excavator Hydraulic Lockout Control
315C Excavator Fine Swing Control - If Equipped
2000/03/20 New 12 Volt AM/FM Radios Are Available {7338}
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Hydraulic Accumulator - Test and Charge
320B, 320B L, 320B LN, 322B L and 322B LN Excavators Supplement Bucket Linkage - Lubricate
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Assemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - Remove
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - Install
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - Disassemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, and 180/H180s
315C Excavator Engine and Machine Warm-Up
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - Assemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, and 180/H180s
315C Excavator Operation Information
A26 Auger Work Tool Systems Auger Planetary - Assemble
320C Excavator Equipment Lowering with Engine Stopped