Vibration Damper and Pulley - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 6V-9120     | Socket (1)     | 1 is     |
B     | 1P-2321     | Combination Puller     | 1     |
Show/hide table
( 1 ) | Tool (A) is a 46 mm socket. |
Start By:
- Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove six bolts (1) and the washers from vibration damper (2). Remove vibration damper (2) from crankshaft pulley (5) .
Note: Inspect the vibration damper for leaks and dents. If either condition exists, replace the vibration damper with a new part.
Show/hide table
Illustration 1 | g00528749 |
- Use Tool (A) and remove nut (3) and the washer from the crankshaft.
Show/hide table
Illustration 2 | g00559259 |
- If necessary, use Tool (B) and remove crankshaft pulley (5) .
Show/hide table
Illustration 3 | g00559308 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install crankshaft pulley (5) with the washer and nut (3) onto crankshaft (4) .
Show/hide table
Illustration 4 | g00559259 |
- Use Tool (A) to tighten nut (3) to a torque of 490 ± 10 N·m (360 ± 7 lb ft). Hit nut (3) with a hammer and torque the bolt again to 490 ± 10 N·m (360 ± 7 lb ft).
- Use six bolts (1) and the washers in order to install vibration damper (2) on the crankshaft pulley.
Show/hide table
Illustration 5 | g00528749 |
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Install".
Caterpillar Information System:
307B Excavator Machine Systems Swing Motor - Assemble
5130 Excavator Hydraulic System Gear Pump (Pump Drive Lubrication)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Long with Medium Pressure
5130 Excavator Hydraulic System Cooler (Pump Drive Lubrication)
307B Excavator Machine Systems Swing Motor - Disassemble
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Clamshell
3046 Engine For Caterpillar Built Machines Flywheel Housing - Remove and Install
317B Excavator Machine System and Attachment Specifications Stick Lines - Short
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Install
307B Excavator Machine Systems Swing Motor - Install
307B Excavator Machine Systems Swing Motor - Remove
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Remove
307B Excavator Machine Systems Swing Drive - Remove
307B Excavator Machine Systems Swing Drive - Disassemble
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Short with Quick Coupler
307B Excavator Machine Systems Swing Drive - Assemble
320B Excavator Machine System Specifications Cab Mounting
307B Excavator Machine Systems Undercarriage Frame - Remove
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Long
307B Excavator Machine Systems Undercarriage Frame - Install
307B Excavator Machine Systems Swing Gear and Bearing - Remove and Install
307B Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
307B Excavator Machine Systems Tank and Filter (Hydraulic) - Install
307B Excavator Machine Systems Auxiliary Hydraulic Pump - Remove