Flywheel Housing - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 135-7575     | Link Bracket     | 1     |
Start By:
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor- Remove and Install".
- Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tool (A), a strap, and a suitable lifting device onto flywheel housing (1) .
Show/hide table
Illustration 1 | g00528388 |
- Remove twelve bolts (2) and the washers that secure flywheel housing (1) to the cylinder block.
- Remove flywheel housing (1). The weight of the flywheel is 30 kg (66 lb).
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check the condition of two dowels (4). If dowels (4) are damaged, use new parts for replacement.
Show/hide table
Illustration 2 | g00528389 |
- Clean old gasket material (3) from the surfaces of the cylinder block and the flywheel housing that contact each other. Install a new gasket on the cylinder block (not shown).
- Install flywheel housing (1) .
Show/hide table
Illustration 3 | g00528388 |
- Install the washers and twelve bolts (2) in order to secure flywheel housing (3) to the cylinder block.
- Remove Tool (A) .
End By:
- Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor- Remove and Install".
- Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar Information System:
317B Excavator Machine System and Attachment Specifications Stick Lines - Short
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Install
307B Excavator Machine Systems Swing Motor - Install
307B Excavator Machine Systems Swing Motor - Remove
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3064 and 3066 Engines for Caterpillar Built Machines Camshaft
307B Excavator Machine Systems Swivel - Assemble
307B Excavator Machine Systems Swivel - Disassemble
317B Excavator Machine System and Attachment Specifications Stick Lines
3064 and 3066 Engines for Caterpillar Built Machines Gear Group (Front)
3046 Engine For Caterpillar Built Machines Flywheel - Install
320B Excavator Machine System Specifications Stick - 6280 mm (247.2 inch)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Clamshell
307B Excavator Machine Systems Swing Motor - Disassemble
5130 Excavator Hydraulic System Cooler (Pump Drive Lubrication)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Long with Medium Pressure
5130 Excavator Hydraulic System Gear Pump (Pump Drive Lubrication)
307B Excavator Machine Systems Swing Motor - Assemble
3046 Engine For Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
307B Excavator Machine Systems Swing Drive - Remove
307B Excavator Machine Systems Swing Drive - Disassemble
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Short with Quick Coupler
307B Excavator Machine Systems Swing Drive - Assemble
320B Excavator Machine System Specifications Cab Mounting