Track Carrier Roller - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 1P-0510     | Bearing and Seal Driver     | 1     |
(B)     | 9U-5985     | Duo-cone Seal Installer     | 1     |
(C)     | 8T-5096     | Dial Indicator     | 1     |
- Thoroughly clean all parts of the track carrier roller prior to assembly.
- Lower the temperature of bearing (13). Use Tooling (A) and a press to install bearing (13) in the inside bore of the carrier roller. Install the bearing until the bearing is even with the shaft counterbore in the carrier roller.
Note: Do not reuse bearings (12) and (13). Use new parts for replacement.
Show/hide table
Illustration 1 | g00367312 |
Note: Bearing (13) is a straight bearing.
- Lower the temperature of bearing (12). Use Tooling (A) and a press to install bearing (12) in the outside bore of the carrier roller. The outside bore can be identified by three threaded holes (H) in the track carrier roller. Install the bearing until the flange on the bearing makes contact with the counterbore in the track carrier roller.
Show/hide table
Illustration 2 | g00367133 |
Note: Bearing (12) has a flange.
- Replace the O-ring seal that is used in collar (11) with a new O-ring seal. Install the O-ring seal in the collar. Put clean oil on the O-ring seal.
Show/hide table
Illustration 3 | g00367112 |
- Use a press to install collar (11) on shaft (8). Install collar (11) until dimension (X) is 107 ± .2 mm (4.21 ± 0.01 inch).
- Use the following procedure to determine shaft end play.
- Install shaft assembly (8) in the track carrier roller without Duo-Cone seal kits.
Note: Do not install the Duo-Cone seal kits in the track carrier roller or collar (11) at this time.
- Install retainer (7) and socket head bolts (5) and (6) on the end of shaft assembly (8) .
- Use Tooling (C) to measure the end play of shaft assembly (8). The end play of the shaft assembly must be 0.20 mm (.008 inch) to 0.5 mm (0.02 inch). Bearing (12) controls the amount of shaft end play.
- Disassemble the track carrier roller, but do not remove collar (11) from shaft (8) .
- Install Duo-Cone seal kit (10) in collar (11) with Tooling (B) .
Note: Refer to Disassembly and Assembly Manual, "Duo-Cone Conventional Seals - Install" for more information.
Note: The rubber seal and all surfaces that make contact with the seals must be clean and dry. After installation of the seals, apply clean SAE 30 oil on the contact surfaces of the metal seals.
Show/hide table
Illustration 4 | g00367057 |
- Install Duo-Cone seal kit (9) in the track carrier roller on the side without three threaded holes with Tooling (B) .
Show/hide table
Illustration 5 | g00365965 |
- Carefully install shaft assembly (8) in the track carrier roller. Install retainer (7) and socket head bolts (5) and (6) .
Show/hide table
Illustration 6 | g00365960 |
- Replace O-ring seal (4) that is used on cover (3) with a new O-ring seal. Put clean oil on O-ring seal (4). Install the O-ring seal on cover (3) .
Show/hide table
Illustration 7 | g00365954 |
- Install cover (3) on the track carrier roller and three socket head bolts (1) .
Show/hide table
Illustration 8 | g00365386 |
- Put the track carrier roller in a vertical position. Fill the track carrier roller with 85 ± 8 mL (2.9 ± .27 oz) of clean SAE 30 oil. Apply 5P-3413 Pipe Sealant on the threads of plug (2). Install plug (2) .
End By: Install the track carrier rollers. Refer to Disassembly and Assembly, "Track Carrier Roller - Install" in this manual.
Caterpillar Information System:
307B Excavator Offset Boom Control - If Equipped
330B Excavator Hydraulic System Operational Checks
M312 Excavator Machine System Pilot Control Valve (Auxiliary)
M318 and M320 Excavators Machine System Specifications Check Valve (Stick Drift Reduction)
5130B Excavator Hydraulic System Operational Checks
M312 Excavator Machine System Solenoid Valve
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Plate Locations and Film Locations
3412 Generator Set Engines Cylinder Block
330B Excavator Hydraulic System Relief Valve (Travel Motor) - Test and Adjust
M312 Excavator Machine System Relief Valve (Line)
315B Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
M315 Excavator Machine System Boom Cylinder
M315 Excavator Machine System Boom - 5.05 m (16.568 ft)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings
M312 Excavator Machine System Lines (Boom Lowering Valve)
315B Excavator Machine Systems Track Roller - Remove
307B Excavator Shipping Specifications - One-Piece Boom
M312 Excavator Machine System Control Valve (Stick Lowering)
315B L Excavator Joystick Controls
3412 Generator Set Engines Cylinder Liner
315B Excavator Machine Systems Track Roller - Install
315B Excavator Machine Systems Track Roller - Disassemble
M312 Excavator Machine System Bucket Linkage - Retention