Accessory Drive
Show/hide table
 | |
| 图 1 | g00594880 |
(1) 定位销从壳体表面伸出的距离如下。 ... 10.0 ± 1.0 mm (0.40 ± 0.04 in)
(2) 轴承安装至孔内的深度如下。 ... 2.0 ± 0.5 mm (0.08 ± 0.02 in)
(3) 齿轮轴轴承的壳体孔 ... 99.075 ± 0.025 mm (3.9006 ± 0.0010 inch)
(4) 新齿轮轴的直径 ... 88.90 ± 0.02 mm (3.500 ± 0.001 inch)
(5) 止推垫圈的厚度 ... 9.77 ± 0.05 mm (0.385 ± 0.002 inch)
轴槽的宽度 ... 10.00 ± 0.13 mm (0.394 ± 0.005 inch)
(6) 惰轮轴先导的内径 ... 120.00 ± 0.05 mm (4.724 ± 0.002 in)
惰轮轴的外径 ... 119.92 ± 0.02 mm (4.721 ± 0.001 inch)
(7) 轴承处惰轮轴的外径 ... 88.90 ± 0.02 mm (3.500 ± 0.001 inch)
空套主动齿轮轴承的外径 ... 99.245 ± 0.020 mm (3.9073 ± 0.0008 inch)
已安装主动齿轮轴承的内径 ... 99.075 ± 0.025 mm (3.9006 ± 0.0010 inch)
(8) 主动齿轮的外径 ... 123.00 ± 0.02 mm (4.843 ± 0.001 inch)
惰轮的内径 ... 123.08 ± 0.03 mm (4.846 ± 0.001 inch)
Caterpillar Information System:
G3606 and G3608 Engines Gas Pressure Regulator - Install
3500B and 3500B High Displacement Generator Set Engines Engine Speed/Timing Sensor - Calibrate
3176C and 3196 Industrial Engines Engine Monitoring System (EMS)
3612 and 3616 Engines Accessory Drive
3406E and 3456 Generator Set Engines Engine Oil Filter Base - Install
3500B Engines and 3500 Engines with EUI Option Digital Sensor Supply
3612 and 3616 Engines Accessory Drive
3176C and 3196 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
3406E and 3456 Generator Set Engines Engine Oil Filter Base - Remove
G3606 and G3608 Engines Vibration Damper Guard - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Install - 3003 Engines
3612 and 3616 Engines Flexible Coupling
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System Electronic Control Module (ECM) - Replace
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Hourmeter Programming OP7
3126B Marine Engine Engine Oil Pan
3126B and 3126E Truck Engines Crankcase Breather
3126B Marine Engine Water Temperature Regulator
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0273 - FMI 00 Turbo Outlet Pressure above normal
Electronic Modular Control Panel II (EMCP II) For PEEC Engines AL Fault Codes
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0275 - FMI 03 Right Turbo Inlet Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0275 - FMI 04 Right Turbo Inlet Pressure short to ground
3612 and 3616 Engines Flywheel
Electronic Modular Control Panel II (EMCP II) For MUI Engines Diagnostic Codes
3612 and 3616 Engines Engine Support