Auxiliary Water Pump - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 1P-0510 | Driver Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the oil hole in the bearing is aligned with the oil passage in housing (15). Use Tooling (B) and a suitable press to install bearing (14) in housing (15). Bearing (14) must be
1.5 ± 0.5 mm (0.06 ± 0.02 inch) below the surface of the housing. The diameter of bearing (14) must be75.000 ± 0.055 mm (2.9527 ± 0.0022 inch) after installation.Show/hide tableIllustration 3 g01252620 - Use Tooling (B) to install lip seal (13) in housing (15). Ensure that the lip of the seal is toward the bearing. Place clean engine oil on the lip seal.
Show/hide table
Illustration 4 g01252420 - Install shaft (7), retaining washers (12), the shims, and the bolts that hold shaft (7) in the housing.
Show/hide table
Illustration 5 g01252622 - Place clean engine oil on the bearing in the housing. Install shaft (1) and retaining washers (11) on shaft (7). Install retaining washers (11) and the bolts on the housing.
Show/hide table
NOTICE Clean water is the only lubricant that is permitted for assembly. DO NOT damage or touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Show/hide tableIllustration 6 g01252650 - Install ceramic seal (10) in the rubber ring. Place clean water on the rubber ring and ceramic seal (10) for lubrication. Use hand pressure and the Tooling that is supplied with the seal group to install the ceramic seal.
Show/hide table
Illustration 7 g01252659 - Remove the spring from carbon seal assembly (9). Place clean water on the inside diameter of the carbon seal assembly for lubrication. Use hand pressure and the Tooling that is supplied with the seal group in order to install carbon seal assembly (9). The face of the seal should make light contact with the shaft.
Show/hide table
Illustration 8 g01252660 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install spring (8) on carbon seal assembly (9).
Show/hide table
Illustration 9 g01252664 - Place clean engine oil on the shaft prior to installation of impeller (6). Install impeller (6) on the shaft. Use a suitable press to install impeller (6). Install the impeller until the distance between the face of the impeller and the face of the shaft is
0.000 ± 0.076 mm (0.0000 ± 0.0030 inch) .Show/hide tableIllustration 10 g00592355 - Install the O-ring seal around adapter (5). Place clean engine oil on the O-ring seal.
- Position adapter (5) on the housing and install the bolts.
Show/hide table
Illustration 11 g00592354 - Place gear (2) on shaft (1) and install the bolts.
- Install O-ring seals (3) and (4) on the housing. Place clean engine oil on the O-ring seals.
Show/hide table
Illustration 1 | g01252599 |
Show/hide table
Illustration 2 | g01252424 |
End By:
- Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar Information System:
G3606 and G3608 Engines Gas Pressure Regulator - Remove
3406E and 3456 Generator Set Engines Air Inlet and Exhaust System
G3500 Engines Auxiliary Water Pump - Disassemble
G3500 Engines Auxiliary Water Pump - Install
3406E Generator Set Engines Sensors and Electrical Components
XQ300, XQ400 Rental Generator Sets Monitoring System
C15 Petroleum Generator Set Engines Cooling System - Check - Overheating
G3500 Engines Auxiliary Water Pump - Remove
3176C and 3196 Engines for Caterpillar Built Machines Water Pump - Test
C15 Petroleum Generator Set Engines Water Temperature Regulator - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
3176C and 3196 Engines for Caterpillar Built Machines Cooling System - Test
3500 and 3500B Engines Fuel Conservation Practices
3408C, 3412C and 3412D High Performance Marine Engines Alternator and Regulator
3406E and 3456 Generator Set Engines Lubrication System
3516B Generator Set Engines with Dynamic Gas Blending Lubrication System Operation
G3500 Engines Water Pump - Remove
3406E and C15 Marine Engines Magnetic Pickup
G3500 Engines Water Pump - Install
3406E and 3456 Generator Set Engines Cooling System
3406E Generator Set Engines Gauges and Indicators
3406E and 3456 Generator Set Engines Housing (Front) - Remove
G3606 and G3608 Engines Gas Pressure Regulator - Disassemble
3500B Engines Water Pump - Disassemble