Gas Pressure Regulator - Disassemble
拆解步骤
开始:
- 拆下气体压力调节器。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将气压调节器 (1) 定位在合适的台面上。
Show/hide table
图 1 | g00592537 |
- 拧松防松螺母 (2) 。
Show/hide table
图 2 | g00595577 |
- 拧松调整螺钉。
注: 计下旋转圈数。 这样做是为了使调整螺钉能够返回到原始位置。
Show/hide table
一定要拧松调整螺钉。 如果不拧松调整螺钉,极大的弹簧压力就有可能造成人身伤害。 |
- 卸下管组件 (4) 。
Show/hide table
图 3 | g00595580 |
- 卸下管组件 (5) 。
- 卸下阀 (6) 。
Show/hide table
图 4 | g00595582 |
- 从滤芯组件 (8) 上卸下阀体 (7) 。
Show/hide table
图 5 | g00595584 |
- 拆解滤芯组件 (8) 。
Show/hide table
图 6 | g00595587 |
(7) 阀体。 (9) 螺钉。 (10) 垫圈。 (11) 滤芯。 (12) 垫圈。 (13) 盖。 |
- 卸下八个螺栓 (15) 。
Show/hide table
图 7 | g00595590 |
- 卸下壳体 (14) 。
- 卸下垫圈 (16) 和弹簧 (17) 。
Show/hide table
图 8 | g00595593 |
- 卸下接头 (18) 。
Show/hide table
图 9 | g00595596 |
- 翻转气压调节器。
- 卸下四个螺栓 (20) 。
Show/hide table
图 10 | g00595600 |
- 卸下壳体 (19) 和垫片。 请检查垫片是否损坏。 如有必要,更换垫片。
- 卸下护圈 (21) 和弹簧 (22) 。
注: 计下旋转圈数。 这样做是为了使螺纹护圈能够返回到合适位置。
注: 小心地将弹簧从壳体上卸下。 弹簧受压。
Show/hide table
图 11 | g00595603 |
- 从壳体 (23) 上卸下十二个螺栓 (24) 。
Show/hide table
图 12 | g00595605 |
- 将盖 (23) 连带轴和膜片一起卸下。
注: 必须将轴和膜片从臂组件上卸下,以便拆卸。
Show/hide table
图 13 | g00595743 |
- 将下部的黄铜接头 (25) 卸下。
Show/hide table
图 14 | g00595744 |
- 翻转壳体。
- 将上部的黄铜接头 (26) 卸下。
Show/hide table
图 15 | g00595746 |
- 卸下垫圈 (27) 。
- 卸下垫圈 (28) 和膜片组件 (29) 。
注: 标记外壳以便正确安装。
Show/hide table
图 16 | g00595747 |
Show/hide table
图 17 | g00595748 |
- 轻敲外壳上部 (30) ,卸下膜片组件 (31) 。
- 卸下喷嘴 (32) 。
- 拆解小型膜片组件 (31) 。
Show/hide table
图 18 | g00595749 |
(33) 阀。 (34) 膜片。 (35) O 形密封圈。 (36) 垫圈。 (37) 适配器。 |
- 卸下大尺寸 T 形管 (38) 。
Show/hide table
图 19 | g00595751 |
- 如有必要,从 T 形管上卸下阀柱塞组件 (39) 。
- 卸下开口销 (40) ,以便能够将轴组件 (41) 推入阀中。 应将轴组件推远,以便接触臂组件。
Show/hide table
图 20 | g00595752 |
- 卸下两个固定夹 (43) 和销 (42) ,以便从调节器壳体卸下臂 (44) 和轴 (41) 。
Show/hide table
图 21 | g00595754 |
- 拆解气压调节器的盖。
Show/hide table
图 22 | g00595755 |
(40) 销。 (41) 轴组件。 (42) 销。 (43) 固定夹。 (44) 臂。 (45) 密封件。 (46) 螺母。 (47) 盖。 |
- 拆解阀柱塞组件。
Show/hide table
图 23 | g00595757 |
(40) 销。 (48) 轴。 (49) 阀室盖。 (50) 衬套。 (51) 护圈。 (52) 螺钉。 |
- 从盖 (23) 上卸下轴组件 (53) 。
Show/hide table
图 24 | g00595758 |
Show/hide table
图 25 | g00595759 |
- 从盖 (23) 上卸下导向装置 (54) 。
- 卸下垫圈 (55) 。
- 卸下膜片 (56) 。
- 拆解大型膜片组件。
Show/hide table
图 26 | g00595761 |
(23) 盖。 (54) 导向装置。 (55) 垫圈。 (56) 膜片。 (57) 接头。 (58) 护圈。 (59) 轴。 |
Caterpillar Information System:
3406E and 3456 Generator Set Engines Housing (Front) - Remove
3406E Generator Set Engines Gauges and Indicators
3406E and 3456 Generator Set Engines Cooling System
G3500 Engines Water Pump - Install
3406E and C15 Marine Engines Magnetic Pickup
G3500 Engines Water Pump - Remove
3516B Generator Set Engines with Dynamic Gas Blending Lubrication System Operation
3406E and 3456 Generator Set Engines Lubrication System
3408C, 3412C and 3412D High Performance Marine Engines Alternator and Regulator
3500 and 3500B Engines Fuel Conservation Practices
G3500 Engines Auxiliary Water Pump - Assemble
G3606 and G3608 Engines Gas Pressure Regulator - Remove
3500B Engines Water Pump - Disassemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E Marine Engine Exhaust Manifold
3500B Engines Water Pump - Assemble
3406E Marine Engine Engine Oil Pan
3406E Marine Engine Auxiliary Water Pump
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Piston Cooling Jet
3406E Generator Set Engines Engine Shutoffs and Engine Alarms
3406E Marine Engine Flywheel Housing
3406E and 3456 Generator Set Engines Housing (Front) - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0546 - FMI 06 Ether Hold Relay short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0546 - FMI 05 Ether Hold Relay open/short to ground