Parallel Setpoint Tuning OP-11
OP11 是编程一些同步设定点的选项。 有关更多信息,请参阅系统操作, "同步调谐步骤"。 本步骤会影响到 P305、P306、P307、P308 和 P309 设定点。 有关设定点的说明,请参阅系统操作, "并联编程 OP5-3"。
维修技师执行此步骤时,必须使发电机组以额定转速运转。 在 OP11 下,使用并联模式开关可启用并联功能。
注: 如果并联模式开关请求并联功能,则执行同步时,OP11 显示将会被同步显示所代替。 同步完成后,显示将返回 OP11。
- 起动发动机并使发动机以额定转速运转。 进入维修模式并输入密码。 有关更多信息,请参阅系统操作, "密码输入 - OP3"。 下显示屏现在应正显示 "OP9"。
- 按下 "SCROLL UP(向上滚动)"键两次。 下显示屏上正显示 OP11。
- 按下 "SELECT(确认)"。 下显示屏上正显示 "P305"。
- 按下 "SCROLL UP(向上滚动)"键或 "SCROLL DOWN(向下滚动)"键。 显示下一设定点及设定点的值。 重复此步骤,直到显示所需设定点。
- 按下 "SELECT(选择)"键。 显示设定点的值。
- 按下 "SCROLL UP(向上滚动)"键或 "SCROLL DOWN(向下滚动)"键调整设定点的值。 如需快速滚过较大范围的值,按住适当的 "SCROLL(滚动)"键。
- 按下 "ENTER(回车)"键。 设定点的值停止闪烁。
- 重复步骤 2、3、4、5、6 和 7,直到调整好全部所需的设定点。
- 按下 "EXIT(退出)"键。 下显示屏上显示 OP1。
- 按下 "EXIT(退出)"键。 显示屏返回正常模式。
Caterpillar Information System:
3500B Engines for Caterpillar Built Power Modules Turbocharger
G3606 and G3608 Engines Connecting Rod Bearings - Remove and Install
3500B Engines Turbocharger
Installation of 185-7733 Sensor Kit {1928} Installation of 185-7733 Sensor Kit {1928}
G3606 and G3608 Engines Prechamber Check Valve - Remove and Install
G3606 and G3608 Engines Magneto Interface - Remove and Install
3500 Engines for Caterpillar Built Generator Sets Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
G3606 and G3608 Engines Gas Needle Valve - Remove and Install
3406E Generator Set Engines Control Panel
3116 Truck Engine Cold Weather Operation
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Install
3406E and 3456 Generator Set Engines Electric Starting Motor
3508B Engine for Caterpillar Built Machines Turbocharger
12H, 140H and 160H Motor Graders Power Train Final Drive - Disassemble
3406E Generator Set Engines Model View Illustrations
3500 Engines Exhaust Manifold
120H and 135H Motor Graders Power Train Final Drive - Assemble
G3500 Engines Engine Oil and Water Pump Drive - Remove
G3500 Engines Engine Oil and Water Pump Drive - Install
G3500 Engines Rocker Shaft and Push Rod - Remove
G3500 Engines Rocker Shaft and Push Rod - Install
3406E and 3456 Generator Set Engines Rocker Arm and Shaft - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0001 - FMI 05 Injector Cylinder 1 open circuit
3512B and 3516B Engines Air Inlet and Exhaust Lines