Vibration Damper - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9392 (1)     | 减振器导向销     | 2     |
1U-9393 (1) | 减振器导向销     | 2     | |
4C-9426 (1) | 减振器导向销     | 2     | |
B     | 8T-0914     | 飞轮导销     | 2     |
C     | 4C-5590     | 防粘结剂     | -     |
Show/hide table
( 1 ) | 所有导销均可用。 是否需要特定导销取决于您的应用。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (B) 安装在曲轴中。
Show/hide table
图 1 | g00556436 |
- 将适当的起吊设备连接至适配器 (3) 上。 适配器 (3) 的重量约为 30 kg (66 lb)。 将适配器 (3) 定位在工具 (B) 上。
- 将工具 (C) 涂敷在将适配器 (3) 固定至曲轴的螺栓上。 安装将适配器 (3) 固定至曲轴的螺栓上。 拆下工具 (B) 后安装其余螺栓。 将螺栓对角拧紧至扭矩 1300 ± 150 N·m (960 ± 110 lb ft)。
- 将工具 (A) 安装在适配器 (3) 内。
- 将适当的起吊设备连接至减振器 (1) 上。 减振器 (1) 的重量约为 188 kg (414 lb)。
Show/hide table
图 2 | g00556435 |
- 将减振器 (1) 上的仪表板标记与适配器对齐。 将减振器 (1) 安装在工具 (A) 上。
- 将工具 (C) 涂抹在螺栓 (2) 上。 安装将减振器 (1) 固定至适配器的螺栓 (2) 。 卸下工具 (A) ,然后安装其余的螺栓 (2) 。 将螺栓 (2) 对角拧紧至扭矩 1150 ± 150 N·m (848 ± 110 lb ft)。
Caterpillar Information System:
3412E, C30 and C32 Marine Engines Heat Exchanger - Install
3054 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3054 Engine for Caterpillar Built Machines Gear Group (Front) - Install
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Block
3054 Engine for Caterpillar Built Machines Gear Group (Front) - Remove
G3408 and G3412 Engines Vibration Damper
SR4 HV and SR4B HV Generators Winding - Test
3054 Engine for Caterpillar Built Machines Lifter Group - Remove and Install
Control Console For CPS361 Pumper, Cement Control Panel
G3408 and G3412 Engines Water Pump
797 Off-Highway Truck Steering System Steering Control Valve
3412E, C30 and C32 Marine Engines Heat Exchanger - Remove
G3408 and G3412 Engines Electric Starting Motor
SR4 HV and SR4B HV Generators General Maintenance Information
G3606 and G3608 Engines Vibration Damper - Disassemble
3406C (PEEC III) Truck Engines Engine Design
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Level Gauge (Dipstick) - Remove and Install
G3606 and G3608 Engines Vibration Damper - Assemble
3054 and 3056 Industrial and Generator Set Engines Engine Design
G3408 and G3412 Engines Water Temperature Regulator
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Engine Oil Scavenge Pump
G3606 and G3608 Engines Flywheel and Ring Gear - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Cooling System
Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902} Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902}