Engine Oil Scavenge Pump
Show/hide table
图 1 | g03836640 |
仰视图 |
Show/hide table
图 2 | g03836639 |
剖面 A-A |
Show/hide table
注意 |
---|
操作之前,必须使用干净的发动机机油润滑泵体,并且泵必须能灵活运转,否则就会导致部件的损坏。 |
Show/hide table
图 3 | g03836638 |
Show/hide table
技术规格 - 1W-8508 扫油泵 | |||
---|---|---|---|
项目 | 数量 | 零件 | 技术规格说明 |
1 | 4 | 3H-2750 螺栓 | 拧紧至扭矩为 |
2 | 2 | - | 装配前,用清洁的发动机机油稍微润滑 O 形密封圈的孔。 |
B | 1 | 1W-8515 齿轮 | 长度为 扫油泵体中新齿轮孔的深度为 |
C | 1 | 161-2510 驱动轴 | 直径为 装配后,新驱动轴的 1W-6005 衬套孔径为 |
D | 1 | 1W-8509 扫油泵体 | 扫油泵体上的 1W-6005 衬套安装深度为 |
E | 1 | 1W-8511 惰轮轴组件 | 自惰轮轴组件末端至齿轮端面的距离为 |
F | 1 | 106-9865 惰轮轴 | 直径为 1W-6005 衬套上的新惰轮轴孔径为 |
3 | 1 | 0S-0484 螺栓 | 采用下述步骤拧紧螺栓:
将驱动齿轮安装到驱动轴组件前,清洁轴和齿轮孔。 1. 敲打驱动齿轮以座合驱动齿轮的锥形部分。 2. 拧紧螺栓至扭矩 3. 重复此步骤直到扭矩不再变化。 |
G | - | - | 从中线穿过轴承孔的衬套接头位置为 45 ± 15 度。 |
H | 2 | 1W-6005 衬套 | 7N-8527 泵盖上的安装深度为 |
J | 2 | 4M-3248 空心定位销 | 空心定位销的延伸量为 |
Caterpillar Information System:
G3408 and G3412 Engines Water Temperature Regulator
3054 and 3056 Industrial and Generator Set Engines Engine Design
G3606 and G3608 Engines Vibration Damper - Assemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Level Gauge (Dipstick) - Remove and Install
3406C (PEEC III) Truck Engines Engine Design
G3606 and G3608 Engines Vibration Damper - Disassemble
SR4 HV and SR4B HV Generators General Maintenance Information
G3408 and G3412 Engines Electric Starting Motor
G3606 and G3608 Engines Vibration Damper - Install
3412E, C30 and C32 Marine Engines Heat Exchanger - Install
3054 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3054 Engine for Caterpillar Built Machines Gear Group (Front) - Install
G3606 and G3608 Engines Flywheel and Ring Gear - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Cooling System
Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902} Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902}
G3408 and G3412 Engines Turbocharger
3054 and 3056 Industrial and Generator Set Engines Lubrication System
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers General Information
3406E and 3456 Generator Set Engines Flywheel - Install
G3408 and G3412 Engines Governor and Magneto Drive
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Joint Assembly for Water Line
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
Caterpillar PRELUB® Diagnostics{1469} Caterpillar PRELUB® Diagnostics{1469}
3412E, C30 and C32 Marine Engines Auxiliary Water Pump - Remove