Water Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-0510 | 起子总成 | 1 |
B | 8T-3034 | 水泵密封起子 | 1 |
C | 6V-1541 | 快速硫化底漆 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 确保所有零件得到彻底清洁和检查。 更换所有损坏或磨损的零件。
- 使用工具 (C) 清洁水泵轴和壳体中的密封件沉头孔。
Show/hide table
图 1 g00544802 - 使用工具 (A) 将唇型密封 ( 1) 安装至壳体 (2) 中。
Show/hide table
图 2 g00544803 - 用钢丝棉擦除泵轴 ( 3)上的沉积物或腐蚀。 除非轴被严重点蚀或大面积腐蚀损坏,否则请勿更换泵轴。
注: 不要使用会在泵轴上留下明显划痕的砂纸。
Show/hide table图 3 g00544832 - 将止推垫圈 (5) 安置于合适位置。 安装螺栓 (4)。
Show/hide table
图 4 g00544833 - 将密封件 (6) 固定到轴 ( 3) 上。 将密封件 (7) 安置于合适位置。 使用工具 (B) 定位密封件。
Show/hide table
图 5 g00544834 - 将弹簧 (8) 安装在轴 ( 3) 上。
Show/hide table
图 6 g00544836 - 将叶轮 (9) 放置于轴 ( 3) 上的合适位置。
Show/hide table
图 7 g00544837 - 安装螺栓 (10) 和垫圈 ( 11)。
Show/hide table
图 8 g00544838 - 将壳体 (12) 安装在壳体 ( 14)上。 确保壳体安装正确。
- 安装固定不同壳体的螺栓 ( 13)。
- 确保泵轴自由转动。
结束:
- 安装水泵。 请参阅 拆解和组装, "水泵 - 安装" 。
Caterpillar Information System:
3412E and C30 Marine Engines Air Starting System
G3606 and G3608 Engines Water Pump - Disassemble
G3606 and G3608 Engines Water Pump - Install
797 Off-Highway Truck Steering System Check Valve (Steering)
G3606 and G3608 Engines Water Pump - Remove
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Liner - Install
365B and 365B Series II Excavators Hydraulic System Graphic Color Codes
3600 Distillate Fuel Engines Trend Data - Record
3406C (PEEC III) Truck Engines Troubleshooting
Gas Engine Driven Chiller Driveline Maintenance Interval Schedule
3054 Engine for Caterpillar Built Machines Fuel Transfer Pump - Install
3606 and 3608 Engines Lubrication System Operation
3054 Engine for Caterpillar Built Machines Fuel Transfer Pump - Disassemble
3406C (PEEC III) Truck Engines Engine Vibration Troubleshooting
3408E and 3412E Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3054 Engine for Caterpillar Built Machines Fuel Transfer Pump - Assemble
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
SR4 HV and SR4B HV Generators Glossary
3054 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Install
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Pump - Remove
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Install