Gear Group (Front) - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Hold accessory drive (7) in position and install bolts (8) . Tighten the bolts to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
Show/hide table
Illustration 1 | g01062060 |
- Install the following items in the front housing: gear (4) , the bearing and shaft (5) and bolt (6) . Tighten bolt (6) to a torque of 240 ± 40 N·m (175 ± 30 lb ft).
- Install the following items in the front housing: gear (3) , the bearing and shaft (1) and bolt (2) . Tighten bolt (2) to a torque of 240 ± 40 N·m (175 ± 30 lb ft).
Note: Ensure that the timing marks on the gears are in alignment.
- Raise the temperature of the sensor plate.
Show/hide table
Always wear protective gloves when handling parts that have been heated. |
- Position the hot sensor plate so that the tab on the sensor plate aligns with Groove (Y) on the crankshaft gear.
Show/hide table
Illustration 2 | g01062136 |
- Push the sensor plate onto the crankshaft gear until the back of the sensor plate contacts the front of the crankshaft gear. Hold the sensor plate on the crankshaft gear in this position until the sensor plate cools and the sensor plate is properly seated.
- Use a feeler gauge in order to measure the clearance between the back of the sensor plate and the front of the crankshaft gear. The measurement should be taken in three places and the clearance should not exceed 0.25 mm (0.010 inch).
Note: Steps 4 through 7 are for Engines (S/N: 3CS1-11999) and (S/N: 2KS1-39999) that have the sensor plate.
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
- Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft Position Sensor - Remove and Install".
- Install the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft Position Sensor - Remove and Install".
- Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
- Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
- Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar Information System:
3500 Spark Ignited Engines Cylinder Head
3406E On-Highway Engine Fuel Transfer Pump - Install
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove
C-10 and C-12 Engines Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3406E On-Highway Engine Engine Oil Pump - Assemble
G3500B Engines Cylinder Head Valves
3176C and 3196 Industrial Engines Compression Brake - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3500 Spark Ignited Engines Valve Mechanism
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Remove
3406E On-Highway Engine BrakeSaver - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Remove
3406E On-Highway Engine BrakeSaver Engine Oil Pump - Disassemble
3406E On-Highway Engine BrakeSaver Engine Oil Pump - Assemble
3176C and 3196 Industrial Engines Compression Brake - Disassemble
3406E On-Highway Engine BrakeSaver - Assemble
Electronic Modular Control Panel II+ (EMCP II+) Instrument Panel - For 3306B and 3406C MUI Engines
3406E On-Highway Engine BrakeSaver Engine Oil Pan - Remove and Install
G3406 Engine Manual Stop Procedure
G3300 Engines Reference Material
3176C and 3196 Industrial Engines Compression Brake - Assemble