Engine Oil Pump - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
B | 1P-0510 | Driver Group | 1 |
Show/hide table
Illustration 1 | g01017356 |
- Install bearings (10) in the body assembly with Tooling (B). The bearing joint should be 30 ± 15 degrees from the center line of the two bearing bores. Install the bearings so the bearings are even with the outside of the body assembly.
- Before final assembly, check the condition and specifications of all of the parts of the engine oil pump. Refer to Specification, "Engine Oil Pump".
Show/hide table
Illustration 2 g01001929 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Lubricate the bearings and idler gear and drive gear (3) with clean engine oil. Install the idler gear and drive gear in body assembly (2).
- Install cover (4). Install bolts (5) in order to secure the cover to body assembly (2).
Note: The engine oil pump must turn freely after assembly. Turn the engine oil pump by hand. Reposition cover (4) if the pump does not turn freely.
- Install bypass valve (6), spring (7), retainer (8), and bolts (9).
- Install the key on the shaft.
Show/hide table
Illustration 3 g01017258 - Install drive gear (1). Install bolt (11). Tighten the bolt to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
G3500B Engines Cylinder Head Valves
3176C and 3196 Industrial Engines Compression Brake - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3500 Spark Ignited Engines Valve Mechanism
3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
C-10 and C-12 Engines Gear Group (Front) - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove
3406E On-Highway Engine Fuel Transfer Pump - Install
3500 Spark Ignited Engines Cylinder Head
C-10 and C-12 Engines Gear Group (Front) - Install
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Remove
3406E On-Highway Engine BrakeSaver - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Remove
3406E On-Highway Engine BrakeSaver Engine Oil Pump - Disassemble
3406E On-Highway Engine BrakeSaver Engine Oil Pump - Assemble