Crankshaft Position Sensor - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Disconnect the harness assembly from crankshaft position sensor (3).
- Remove bolt (1) and the washer.
- Remove crankshaft position sensor (3) and bracket (2) as a unit from the front housing.
- Inspect the condition of the O-ring seal on crankshaft position sensor (3). Replace the O-ring seal, if necessary.
Show/hide table
| |
| Illustration 1 | g01022903 |
Show/hide table
| |
| Illustration 2 | g01064046 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install crankshaft position sensor (3) and bracket (2) as a unit into the front housing.
- Install bolt (1) and the washer.
- Connect the harness assembly to crankshaft position sensor (3).
- Calibrate the engine speed-timing. Refer to Electronic Troubleshooting for more information.
Show/hide table
|
| |
| Illustration 3 | g01064046 |
Show/hide table
|
| |
| Illustration 4 | g01022903 |
Caterpillar Information System:
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3500 Spark Ignited Engines Valve Mechanism
3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3500 Spark Ignited Engines Piston and Rings
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Install
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Remove
3176C and 3196 Industrial Engines Compression Brake - Install
G3500B Engines Cylinder Head Valves
3406E On-Highway Engine Engine Oil Pump - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
C-10 and C-12 Engines Gear Group (Front) - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove
3406E On-Highway Engine Fuel Transfer Pump - Install
3500 Spark Ignited Engines Cylinder Head
C-10 and C-12 Engines Gear Group (Front) - Install
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Remove
3406E On-Highway Engine BrakeSaver - Disassemble