Crankshaft - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8T-5096 | 千分表总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将曲轴主轴承 (3) 的上半部分定位到缸体中。 将曲轴主轴承 (3) 的下轴瓦放到主轴承盖中。
- 将适当的起吊设备拧紧在曲轴上并且将曲轴放在缸体中。 曲轴的重量约为
129 kg (285 lb) 。 - 安装曲轴止推轴承 (4)。
Show/hide table
图 2 g01022767 - 安装曲轴主轴承盖 (2) ,零件号朝向缸体右侧。 确保曲轴主轴承盖 (2) 的编号为 1 到 7。 编号应从发动机前部开始。 将清洁的机油或 Molylube 涂抹到螺栓螺纹和垫圈上。 安装螺栓 (1)。 将螺栓上紧到
95 ± 5 N·m (70 ± 4 lb ft) 的扭矩。 - 在每个螺栓头上标上标记。 将螺栓再转动 90 ± 5度(1/4圈)。
- 用工具 (A) 检查曲轴的端隙。 端隙必须为
0.10 mm (0.004 in) 到0.50 mm (0.020 in) 。
Show/hide table
注意 |
---|
确保曲轴主轴承锁片与缸体和曲轴主轴承盖中的槽相互啮合。 |
Show/hide table
图 1 | g01022781 |
结束:
- 安装活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 安装"。
- 安装飞轮壳体。 请参阅拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装前壳体。 请参阅拆解和组装, "壳体(前) - 安装"。
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Install
3114, 3116, and 3126 Industrial and Generator Set Engines Fuel System - Prime
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
3406E On-Highway Engine Fuel Filter Base - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3406C (PEEC III) Truck Engines General Information
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3306B Industrial Engine Turbocharger - Remove
3406E On-Highway Engine Rocker Arm - Disassemble
3306B Industrial Engine Turbocharger - Install
3406E On-Highway Engine Rocker Arm - Assemble
3176C and 3196 Industrial Engines Cylinder Head - Remove
3406C Engines for Caterpillar Built Machines Flywheel
3524B Engines for Off-Highway Trucks Excessive White Smoke
3406E On-Highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E On-Highway Engine Rocker Arm and Shaft - Install
3406E and 3456 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Disassemble
C-12 Truck Engine Cylinder Liner