Pistons and Connecting Rods - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-3601 | 活塞环扩展器 | 1 |
B | 5P-8639 | 液压压力 | 1 |
8F-0024 | 软管组件 | 1 | |
1P-2375 | 连接器 | 1 | |
1P-2376 | 连接器 | 1 | |
5P-9725 | 液压油缸 | 1 | |
5P-8651 | 隔套 | 1 | |
5P-8649 | 适配器 | 1 | |
5P-8650 | 适配器 | 1 |
开始:
- 卸下活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将活塞环 (1) 从活塞冠 (2) 上拆下。
- 拆除螺塞 (3) 和活塞销 (5)。
- 将活塞冠 (2) 从活塞裙 (4) 和连杆 (7) 上分离。
Show/hide table
注意 在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。
- 沿长度 (X) 加热连杆 (7)。 长度 (X) 的最大尺寸为
85.0 mm (3.35 in) 。 - 使用工具 (B) 拆掉旧轴承 (6),同时安装新轴承 (6)。
- 轴承接头必须在箭头所示位置之一的 10 度以内。
Show/hide table
图 1 | g01062444 |
Show/hide table
图 2 | g01062446 |
Caterpillar Information System:
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3406C (PEEC III) Truck Engines General Information
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3406E On-Highway Engine Engine Oil Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
3406E On-Highway Engine Fuel Filter Base - Remove and Install
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove
3114, 3116, and 3126 Industrial and Generator Set Engines Fuel System - Prime
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Install
3306B Industrial Engine Turbocharger - Remove
3406E On-Highway Engine Rocker Arm - Disassemble
3306B Industrial Engine Turbocharger - Install
3406E On-Highway Engine Rocker Arm - Assemble