Crankshaft Main Bearings - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 2P-5518     | 轴承工具     | 1     |
B     | 8T-5096     | 千分表总成     | 1     |
C     | 6V-4876     | 润滑     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 组装之前,在曲轴主轴承上涂上清洁的发动机机油。 确保曲轴主轴承背面的锁键适合曲轴主轴承盖和缸体的凹槽。
Show/hide table
注意 |
---|
确保曲轴主轴安装在正确的位置。 使用两个零件号不同的零件,数量分别是3个和 4 个。 4个具有相同零件号的零件应安装到曲轴主轴承 2、3、5 和 6 上。 3个具有相同零件号的零件应安装到曲轴主轴承 1、4 和 7 上。 止推板仅安装在中间曲轴主轴承上。 |
- 将止推片 (4) 安装到凸轮轴上。
Show/hide table
图 1 | g01022781 |
- 使用工具 (A) 将曲轴主轴承 (3) 新的上轴瓦安装到缸体内。 轴承的这一半有油孔。 不要用机油涂抹曲轴主轴承背面。
- 在曲轴主轴承盖 (2) 中安装曲轴主轴承的新下半部分。 不要用机油涂抹曲轴主轴承背面。
Show/hide table
图 2 | g01022767 |
- 在缸体上安放主轴承盖 (2) 到位。 将清洁的发动机机油或工具 (C) 涂抹到螺栓螺纹和垫圈表面。 安装螺栓 (1) 。
Show/hide table
注意 |
---|
安装曲轴主轴盖 时,应使零件号朝向发动机右侧。 曲轴主轴盖通过位于底部表面的冲压号码 1 到 7 进行识别。 止推板安装在曲轴主轴承上的原始位置中。 |
- 将螺栓上紧到 95 ± 5 N·m (70 ± 4 lb ft) 的扭矩。 在每个螺栓头上标上标记。 将每个螺栓都再拧紧90 ± 5度(1/4圈)。
- 用工具 (B) 检查曲轴端隙。 端隙必须为 0.10 mm (0.004 in) 到 0.50 mm (0.020 in)。
注: 曲轴端隙由曲轴止推板 (4) 控制。 止推板 (4) 位于曲轴的中间。
End By: 安装油底壳。 请参阅 拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
3114, 3116, and 3126 Industrial and Generator Set Engines Fuel System - Prime
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
3406E On-Highway Engine Fuel Filter Base - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3406C (PEEC III) Truck Engines General Information
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3406E On-Highway Engine Engine Oil Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Install
3306B Industrial Engine Turbocharger - Remove
3406E On-Highway Engine Rocker Arm - Disassemble
3306B Industrial Engine Turbocharger - Install
3406E On-Highway Engine Rocker Arm - Assemble
3176C and 3196 Industrial Engines Cylinder Head - Remove
3406C Engines for Caterpillar Built Machines Flywheel
3524B Engines for Off-Highway Trucks Excessive White Smoke
3406E On-Highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E On-Highway Engine Rocker Arm and Shaft - Install
3406E and 3456 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove