Cylinder Head - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 185-3630 | 带式扳手总成 | 1 |
开始:
- 拆除配气机构盖的底座。 请参阅拆解和组装 , "气门机构罩盖底座 - 拆卸和安装" 。
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装 , "摇臂轴和推杆 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下螺栓 (1)。 拆下夹子 (2)。
- 将传感器从发动机配线线束 ( 3) 上断开。
- 拆除传感器。
Show/hide table
图 2 g00517351 - 卸下螺栓 (5)。 断开管组件 (4) 并拆除 O 形密封圈。
- 拆下螺栓 (7)。 断开管组件 (6) 并拆除 O 形密封圈。
Show/hide table
图 3 g00517354 典型实例 - 使用工具 (A) 卸下燃油滤清器 ( 8)。 断开软管 (9)。 立即堵住所有开口。
- 松开螺栓 (11)。 断开配线线束 (10)。
Show/hide table
图 4 g00517355 典型实例 - 断开传感器接头 ( 13) 和夹子 (12)。 拆下夹子 (14) 和螺栓。
Show/hide table
图 5 g00517356 典型实例 - 拆下螺栓 (15)。
- 拆下出水歧管 (16)。
Show/hide table
图 6 g00517359 - 拆下缸盖螺栓 (17)。
- 将出水歧管密封垫 ( 18) 从缸盖 (19) 上拆除。
Show/hide table
图 7 g00517361 - 将合适的起吊设备连接到缸盖 ( 19)。 将缸盖 (19) 从缸体上拆下。 缸盖 (19) 的重量为
135 kg (300 lb) 。 - 将缸盖密封垫 (20) 和O 形密封圈 (21) 从缸体上拆下。
Show/hide table
图 1 | g00517348 |
Caterpillar Information System:
3406E On-Highway Engine Rocker Arm - Assemble
3306B Industrial Engine Turbocharger - Install
3406E On-Highway Engine Rocker Arm - Disassemble
3306B Industrial Engine Turbocharger - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Install
3114, 3116, and 3126 Industrial and Generator Set Engines Fuel System - Prime
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
3406E On-Highway Engine Fuel Filter Base - Remove and Install
3406C Engines for Caterpillar Built Machines Flywheel
3524B Engines for Off-Highway Trucks Excessive White Smoke
3406E On-Highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E On-Highway Engine Rocker Arm and Shaft - Install
3406E and 3456 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Disassemble
C-12 Truck Engine Cylinder Liner
3524B Engines for Off-Highway Trucks Too Much Vibration
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Assemble
3406E On-Highway Engine Housing (Front) - Remove
3406E On-Highway Engine Housing (Front) - Install
3176C Engine Cylinder Liner