Fuel Filter Base - Remove and Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 2P-8250 | Strap Wrench | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Turn the fuel supply to the “OFF” position.
- Disconnect hose assemblies (1) and (2).
- Use Tooling (A) to remove fuel filter (3) from the fuel filter base.
- Remove the bolts that fasten the fuel filter base to the engine. Remove fuel filter base (4).
Show/hide table
| |
| Illustration 1 | g00516824 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install fuel filter base (4) on the engine.
- Install fuel filter (3) on the fuel filter base. Follow the directions on the fuel filter for the correct installation procedure.
- Connect hose assemblies (1) and (2) to the fuel filter base.
- Turn the fuel supply to the “ON” position.
- Remove the air from the system. Refer to Testing and Adjusting, "Fuel System - Prime".
Show/hide table
|
| |
| Illustration 2 | g00516824 |
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3406C (PEEC III) Truck Engines General Information
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3406E On-Highway Engine Engine Oil Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
G3300 Engines Valve Data Sheet
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove
3114, 3116, and 3126 Industrial and Generator Set Engines Fuel System - Prime
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Install
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft - Install
3306B Industrial Engine Turbocharger - Remove
3406E On-Highway Engine Rocker Arm - Disassemble
3306B Industrial Engine Turbocharger - Install
3406E On-Highway Engine Rocker Arm - Assemble
3176C and 3196 Industrial Engines Cylinder Head - Remove