Gear Pump - Air to Air After Cooler (ATAAC) Fan System
Show/hide table
Illustration 1 | g06144762 |
ATAAC gear pump orientation view (1) Gear Pump (2) Pump Inlet (3) Pump Outlet |
Show/hide table
Illustration 2 | g06144754 |
Example of pump rotation and flow (2) Pump Inlet (3) Pump Outlet (4) Idler Gear (5) Drive Gear |
The ATAAC pump is a fixed displacement gear pump on the left side of the engine.
The drive shaft turns drive gear (5), which forces idler gear (4) to turn. A seal is formed by the gears against the pump housing. As the gears turn, oil enters through pump inlet port (2). The oil is trapped between the teeth and the pump housing. The oil is pulled around the outside of the gears. The oil is then forced out of pump outlet port (3).
Since gear motor (1) is a fixed displacement gear-type pump, the oil flow rate is directly proportional to the speed of the engine.
Caterpillar Information System:
C175-20 High Altitude Engine for Caterpillar Built Machines Exhaust Elbow - Remove and Install - Eight Turbocharger Configuration
HFW222 SC Felling Head Bearing for Grapple Arm - Lubricate
745 & 740 GC Articulated Truck Gear Motor (Hydraulic Fan)
New Engine Software for Certain C4.4 Machine Engines {1920} New Engine Software for Certain C4.4 Machine Engines {1920}
HFW222 SC Felling Head Bearing for Accumulator Arm - Lubricate
A New Suspension Gland and Backup Ring are Now Available on Certain 795F and 797 Off-Highway Trucks {7200, 7201} A New Suspension Gland and Backup Ring are Now Available on Certain 795F and 797 Off-Highway Trucks {7200, 7201}
740 Ejector Articulated Truck Piston Pump (Hydraulic Fan)
HFW222 SC Felling Head Operating Technique Information
C7.1 Engines and Generator Sets ARD Nozzle Heater - Test
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
C15 and C18 Engines for Caterpillar Built Machines Turbocharger
C15 and C18 Engines for Caterpillar Built Machines Water Lines
C175-20 High Altitude Engine for Caterpillar Built Machines Turbocharger - Remove - Eight Turbocharger Configuration - High Pressure
AP600F and AP655F Asphalt Pavers Engine Supplement Gear Motor (Fan Drive) - Disassemble
AP600F and AP655F Asphalt Pavers Engine Supplement Gear Motor (Fan Drive) - Assemble
New Position Sensor Is Now Used on Certain Cat® Products {5645, 7220} New Position Sensor Is Now Used on Certain Cat® Products {5645, 7220}
C15 and C18 Engines for Caterpillar Built Machines Electronic Control Wiring Group
Installation Procedure for the Product Link® PL641 on Certain Caterpillar Telehandlers {1408, 7338, 7490, 7602, 7606} Installation Procedure for the Product Link® PL641 on Certain Caterpillar Telehandlers {1408, 7338, 7490, 7602, 7606}
Installation of the 522-3935 SATCO Standby Kit on the 538 GF Forest Machine {5069, 5117} Installation of the 522-3935 SATCO Standby Kit on the 538 GF Forest Machine {5069, 5117}
HFW222 SC Felling Head Disc Saw Tooth - Inspect/Replace
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Service Brake Discs - Check
Installation Procedure for the Product Link® PL641 on Certain Caterpillar Telehandlers {7606, 7620} Installation Procedure for the Product Link® PL641 on Certain Caterpillar Telehandlers {7606, 7620}
PM-620 and PM-622 Cold Planer Engine Supplement Diesel Exhaust Fluid Pump - Remove and Install
A New Plate is Now Used in the Mud Guard Group on Certain 770G and 772G Off-Highway Trucks {4220, 7150, 7252} A New Plate is Now Used in the Mud Guard Group on Certain 770G and 772G Off-Highway Trucks {4220, 7150, 7252}