Rotor Drive Clutch - Remove and Install
Start By:
- Remove the rotor drive belt.
- Remove the clean emissions module (or muffler if equipped).
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g06102787 - Remove three bolts (2). Remove two bolts (3). With the assistance of another person, remove access panel (4). The weight of access panel (4) is approximately
68 kg (150 lb) Show/hide tableIllustration 2 g06130009 - Remove two bolts (6). Disconnect hose assembly (5) and place entire assembly out of the way.
Show/hide table
Illustration 3 g06130045 - Remove two bolts (7). Remove belt guard (9).
- After removing belt guard (9), reinstall bolts (7) to hold access cover (8) in place.
Show/hide table
Illustration 4 g06130057 - Remove two bolts (11).
- Remove four bolts (10). Repeat process for opposite side of mounting bracket (12). With the assistance of another person, remove mounting bracket (12). The weight of mounting bracket (12) is approximately
34 kg (75 lb) Show/hide tableIllustration 5 g06130084 - Attach a suitable lifting device to rotor drive clutch assembly (14). The weight of rotor drive clutch assembly (14) is approximately
200 kg (441 lb) . - Remove remaining ten bolts (13). Remove rotor drive clutch (14).
- Install rotor drive clutch assembly (14) in the reverse order of removal.
Caterpillar Information System:
C7.1 Engines and Generator Sets Valve Lash Is Excessive
C7.1 Engines and Generator Sets Power Is Intermittently Low or Power Cutout Is Intermittent
C7.1 Engines and Generator Sets Oil Pressure Is Low
C7.1 Engines and Generator Sets Oil Contains Fuel
994K Wheel Loader Machine Systems Cab - Remove and Install
C7.1 Engines and Generator Sets Oil Contains Coolant
980L Tier 3 Wheel Loader Machine System Lift Cylinder - Remove and Install
980L Tier 3 Wheel Loader Machine System Tilt Lever and Tilt Link - Remove and Install
C7.1 Engines and Generator Sets Oil Consumption Is Excessive
793D Off-Highway Truck Power Train Torque Converter
C7.1 Engines and Generator Sets NRS Mass Flow Rate Problem
C7.1 Engines and Generator Sets NRS Exhaust Gas Temperature Is High
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Water Pump - Remove and Install
An Improved Coupler Cylinder for Pin Grabber Is Now Used on Certain Excavators {5133} An Improved Coupler Cylinder for Pin Grabber Is Now Used on Certain Excavators {5133}
A New Procedure to Install the Front Axle Grease Line Protective Cover Is Now Available on Certain C & C2 Series Articulated Trucks {0679, 3013, 3278, 3282, 7150, 7450, 7510, 795C} A New Procedure to Install the Front Axle Grease Line Protective Cover Is Now Available on Certain C & C2 Series Articulated Trucks {0679, 3013, 3278, 3282, 7150, 7450, 7510, 795C}
XT6 ES Hose Replacement Procedure on Certain Asphalt Compactors {5057} XT6 ES Hose Replacement Procedure on Certain Asphalt Compactors {5057}
Replacing the Implement Pump on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {3203, 5070, 5073} Replacing the Implement Pump on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {3203, 5070, 5073}
Rework Procedure to Install the Counterweight and Treat the Subframe Weld on the C-Series Knuckleboom Loaders {0679, 4150, 7050, 7051, 7056} Rework Procedure to Install the Counterweight and Treat the Subframe Weld on the C-Series Knuckleboom Loaders {0679, 4150, 7050, 7051, 7056}
Check the Tilt Lever on R3000H Load Haul Dump Machines {6107} Check the Tilt Lever on R3000H Load Haul Dump Machines {6107}
Check the Hydraulic Tank Baffle on Certain Load Haul Dump Machines {5056} Check the Hydraulic Tank Baffle on Certain Load Haul Dump Machines {5056}
990K Wheel Loader Systems Steering Control Support
980L Tier 3 Wheel Loader Machine System Window Wiper and Wiper Motor (Front) - Remove and Install
980L Tier 3 Wheel Loader Machine System Window Wiper and Wiper Motor (Rear) - Remove and Install
980L Tier 3 Wheel Loader Machine System Seat - Remove and Install